background image

8

* Depending on version

CLOCK *
This set has a clock that can either be manually
set by you or can be automatically updated via
the RDS signal.

SETTING THE CLOCK (MANUALLY)
• Enter the Initial Settings menu.

• Select option 'CLK'.

 

• Alter the Choice to 'MAN'.

 ,

– Display shows e.g. '00:00' (24 hour format) or

'AM 12:00' (12 hour format).

• To adjust the Clock

– The clock starts operating from the selected

time.

• Leave the Initial Settings menu :

– 10 seconds after any key operation, the display will

always show the time when clock mode is activated.

RDS CLOCK * (AUTO UPDATED)
You can select an automatic update of the clock
via the RDS radio signal.
• See INITIAL SETTINGS; select Option 'CLK'

and set Choice to 'AUTO'.

– The transmitted time via RDS can be incorrect.

SDVC (SPEED DEPENDENT VOLUME
CONTROL)  AND SPEED WARNING
• See INSTALLATION for connection instructions.

SDVC *
To compensate for surrounding noise this function
automatically increases the volume of the set as
a result of the car's speed. Four compensation
levels can be selected. Level 1 gives a small
increase up to level 4 which gives a greater
increase. See 'INITIAL SETTINGS' option SDVC
to alter the level until you find one which suits
your car.

Speed Warning *
You can use this function to inform you that you
are exceeding a certain speed. Always obey
the Highway Code and current traffic
restrictions and conditions!

To calibrate :
To avoid unnecessary distraction we advise
that this procedure is carried out with the
help of somebody else.
1 While stationary, hold down the 'SPEED' key

turn on the set.

2 The set mutes. Display shows 'CALIBRAT' and

then '50 KM/H'.

3 Now drive to 50KM/H (30MPH)

(Always obey the Highway Code and
current traffic restrictions and conditions!)

4 Once 50KM/H (30MPH) is reached briefly press

'SPEED' key :

You hear a beep and display shows 'CALIB
OK' and then 'SDVC ON'.

5 Now turn the set off and on again to return to

normal operation.
Level 3 is chosen for 'SDVC' and 'SPD' is set to
KM/H in 'INITIAL SETTINGS'.

SPECIAL FUNCTIONS

Summary of Contents for CD 2100 -



















Reviews: