background image

12

BEFORE RUNNING YOUR VEHICLE 

 / / / / / / / / / / / / / / /

 

/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

TO IMPROVE RUN TIMES

 

»

Clean and oil bearings often. If bearings are dirty, they  

will increase friction and cause reduced performance.

 

»

Keep your vehicle clean and maintained.

 

»

Allow more airflow to the ESC and motor.

 

»

Change the gearing to a lower ratio.  

A lower ratio decreases the operating temperature of the 

electronics. Use a smaller pinion gear or larger spur gear  

to lower the gear ratio.

 

»

Use a battery pack with a higher mAh rating.

RUN TIME 

 / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

 

/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / 

1

  Check for free suspension movement. All suspension arms 

and steering components should move freely. Any binds will 

cause the vehicle to handle poorly.

2

  Charge the battery.

3

  Check the calibration of the ESC. If recalibration is required, 

follow the setup instructions.

4

  Adjust the transmitter settings to your desired  

configuration.

DRIVING PRECAUTIONS

 

»

Maintain sight of the vehicle at all times.

 

»

Routinely inspect the vehicle for loose wheel hardware.

 

»

Routinely inspect the steering assembly for any loose  

hardware. Driving the vehicle off-road can cause fasteners  

to loosen over time.

 

»

Do not drive the vehicle in tall grass. Doing so can damage 

the vehicle or electronics.

 

»

Stop driving the vehicle when you notice a lack of power.  

Driving the vehicle when the battery is discharged can  

cause the receiver to power off. If the receiver loses power, 

you will lose control of the vehicle. Damage due to an  

over-discharged battery is not covered under warranty.

 

»

Do not apply forward or reverse throttle if the vehicle is  

stuck. Applying throttle in this instance can damage the  

motor or ESC.

 

»

After driving the vehicle, allow the electronics to cool before 

driving the vehicle again. Remove the body of the vehicle  

to reduce cooling time.

The largest factor in run time is the  

capacity of the battery pack. A larger 

mAh rating increases the amount  

of run time experienced.
The condition of a battery pack is also 

an important factor in both run time 

and speed. The battery connectors  

may become hot during driving.  

Batteries will lose performance  

and capacity over time.
Driving the vehicle from a stop to  

full speed repeatedly will damage  

the batteries and electronics over  

time. Sudden acceleration will also  

lead to shorter run times.

Summary of Contents for SLICK ROCK





















Reviews: