VAT 01 Series Installation, Operating And Maintenance Instructions Download Page 5

 

Installation, Operating, and Maintenance Instructions 

Series 01, DN 16 - 50 (5/8" - 2")

 

 

 

 

VAT Vakuumventile AG, CH-9469 Haag, Switzerland 
Tel +41 81 771 61 61   Fax +41 81 771 48 30   [email protected]   www.vatvalve.com 

271691EB

 

2009-03-09 

5/15 

 

 

2.3  Admissible forces 

 

Tighten mounting screws of the flanges uniformly in crosswise order. Observe the maximum torque of 
9 Nm / 6.5 lbf 

.

 ft for CF flanges

 

 

Forces from evacuating the system, from the weight of other components, and 
from baking can lead to deformation of the valve body and to malfunction of 
the valve. The stress has to be relieved by suitable means, e.g. bellows 
sections. The following forces are admissible: 
 
Axial tensile or compressive force «FA»: 500 N / 112 lbf 
Bending moment «M»: 

30 Nm / 22 lbf 

.

 ft 

 
If a combination of both forces («FA» and «M») occurs, the values mentioned 
above are invalid. Please contact VAT for more information. 

 

 

2.4  Connections 

 

2.4.1  Compressed air connection 

 

 

Connect compressed air only if 
  -  valve has been installed into the vacuum system 
  -  moving parts cannot be touched 

With solenoid: 

Connect compressed air to

 IN

 (internal thread R 

1

/

8

“, 

1

/

8

“ NPT for USA) 

Without solenoid:  Connect compressed air to

 OPEN

 and 

CLOSE

 (internal thread M5)  

Compressed air pressure (min. - max. overpressure): 5.0 - 7 bar / 72.5 - 100 psig 

Use only clean, dry or slightly oiled air! 

 

2.4.2  Compressed air connection: Solenoid separate, without solenoid 

 

Ordering No. 010 . . - . E12/22 

Pneumatic actuator: single acting  
with opening spring (NO) 
3/2-way valve 

Compressed air connection:  
Internal thread R

1

/

8

“ (

1

/

8

“ NPT for USA) 

Compressed air to connection <2>:  
valve closes 

Ordering No. 010 . . - . E11/21 

Pneumatic actuator: single acting  
with closing spring (NC) 
3/2-way valve 

Compressed air connection:  
Internal thread R

1

/

8

“ (

1

/

8

“ NPT for USA) 

Compressed air to connection <2>:  
valve opens 

Ordering No. 010 . . - . E14/24 

Pneumatic actuator: double acting 
4/2-way valve 

Compressed air connection:  
Internal thread 

1

/

8

“   

Compressed air to connection <A>:  
valve opens 

Compressed air to connection <B>:  
valve closes 

1

2

 

1

2

 

 

Summary of Contents for 01 Series
















Reviews: