VAT 01 Series Installation, Operating And Maintenance Instructions Download Page 2

 

Installation, Operating, and Maintenance Instructions 

Series 01, DN 16 - 50 (5/8" - 2")

 

 

 

 

VAT Vakuumventile AG, CH-9469 Haag, Switzerland 
Tel +41 81 771 61 61   Fax +41 81 771 48 30   [email protected]   www.vatvalve.com 

271691EB

 

2009-03-09 

2/15 

 

Imprint: 
 
 
Manufacturer 

VAT Vakuumventile AG, CH-9469 Haag, Switzerland 

 
Website 
www.vatvalve.com

 

 
Phone 
+41 81 771 61 61

 

 
Fax 
+41 81 771 48 30 

 
Email 
[email protected] 

 

 

Publisher 

VAT Vakuumventile AG, CH-9469 Haag, Switzerland 

 

 

Editor 

VAT Vakuumventile AG, CH-9469 Haag, Switzerland 

 

 

Print 

VAT Vakuumventile AG, CH-9469 Haag, Switzerland 

 

 

Copyright 

© VAT Vakuumventile AG 2008 

 

 

 

No part of these Instructions may be reproduced in any way (photocopies, microfilms or any 
other reproduction processes) nor may it be manipulated with electronic systems, duplicated or 
distributed without written permission from VAT. Offenders are liable to pay damages. 

 

 

 

The original VAT firmware and updated state of the art versions of the VAT firmware are 
intended for use with VAT products. The VAT firmware contains a limited, time unlimited user 
license. The VAT firmware may not be used for purposes other than those intended nor is it 
permitted to make copies of the VAT firmware. In particular, it is strictly forbidden to give copies 
of the VAT firmware to other people. 

 

 

 

The use of trade names, brand names, trademarks, etc. in these Instructions does not entitle 
third parties to consider these names to be unprotected and to use them freely. This is in 
accordance with the meaning of the laws and acts covering brand names and trademarks. 

 

Summary of Contents for 01 Series
















Reviews: