background image

Thank you

 for purchasing your printing equipment form Vastex International Inc.  

   Vastex has been designing and building printing equipment since 1960. We have knowledge and experi-
ence, and are proud to supply the printing industry with quality equipment at an affordable price. You can 
be confident your purchase will give you years of trouble free service. 

 

Steel Pallets  

 

Floating Print heads allows multiple heads down 

 

Available up to 4 table  color 

 

Expandable from 1x1 to 4x4 

 

1/2”, 5/16”, 3/4” Wrenches. 

 

OR METRIC: 

8mm, 13mm, 19mm. 

Introduction 

Features 

Safety 

Intended Use: 

This equipment is intended for performing manual screen printing of fabric items, particularly garments.  This equip-
ment must not be used in a manner contrary to what is described in this manual. 

Safety: 

 

The operator should read and understand this manual before operating this equipment. Store manual and safety 
information near equipment for easy access to operators. 

 

Keep children and pets clear of the work area. 

 

Do not sit or stand on printer. 

 

The print heads utilize heavy duty springs to hold the screen in the raised position. These springs generate a lot of 
force. Care must be taken when installing and removing the print head lifting springs. 

 

Do not operate printer without print head stop bar in place. 

 

Do not allow print heads to swing into their raised position unrestrained. 

Tools Required 

Pg.2

Summary of Contents for V-100
















Reviews: