VASTEX E-200 series Assembly And Operation Instructions Manual Download Page 1

Page: 1 / 12

Doc. # 01-04-025H

Vastex E-mail assistance

Purchasing & Product Info:

[email protected]

Electrical Support:

[email protected]

Tech Support, Mechanical Setup, and Operation:

[email protected]

Screen Printing Issues & Support:

[email protected]

Vastex International, Inc.
7 Emery St
Bethlehem, Pa. 18015 USA
Phone# 610 625-2702 Fax# 610 625-2775
Web Site www.vastex.com

Authorized Representative in Europe:
Certification Experts BV
Nieuwstad 100 1381 CE Weesp,
The Netherlands
Tel : + 31 (0) 294 – 48 33 55
Fax : + 31 (0) 294 – 41 46 87

Year of Manufacture:

20____

Original Instructions

Serial Number:

VTX

(Please log your machine's serial number and date of purchase for future reference.)

Date:

/ /

Electrical Drawing #:

Revision:

E-200 LED Exposing Unit

Assembly and Operation Instructions

Contents Pg.

Introduction, Machine Specifications

Safety Information

Assembly Instructions

Operating Instructions

Maintenance 6

Troubleshooting 7-8

Emulsion Tip

9-10

01-00-005/015 Warranty/Terms and Conditions

E200-2128

E200-2331

Summary of Contents for E-200 series













Search results

Summary of Contents for E-200 series

Reviews:

Related manuals for E-200 series

Brands by name

Popular brands

VASTEX E-200 series, Assembly And Operation Instructions Manual

Search results

Summary of Contents for E-200 series

Reviews:

Related manuals for E-200 series

Brands by name

Popular brands