background image

VSD-1MC-20(40) 

Page 2 

This guide will inform the electrician on proper wiring and installation procedures 
and, will also inform the user on how to use the VSD-1MC-20(40) module. 
 
The manufacturer recommends that the following installation instructions be 
followed to as closely as possible, and that all work be performed by a certified 
electrician. Failure to do so may void the warranty. 

Description

 

The VSD-1MC-20(40) module is designed to control a variable speed fan 
according to a 0-10 V or a 4-20 mA signal from a master system resulting in a 
uniform air environment for your livestock or crop. The output can be operating 
manually with the switch and potentiometer on the faceplate. The VSD-1MC is 
offered in 3 different models which are VSD-1MC, VSD-1MC-20 or VSD-1MC-40. 
This manual covers the VSD-1MC-20 and VSD-1MC-40. The module operates 
on 115/230V and 50/60Hz. 

The VSD-1MC-20(40) comes in a PVC non-corrosive enclosure that is protected 
from dust and humidity. The VSD-1MC-20(40) is covered by a complete two-year 
warranty. 

Unpacking 

Unpack the VSD-1MC-20(40) module and inspect contents for damage. Should 
the contents appear to be damaged, contact your local distributor to return the 
equipment. 
 

The package should contain the following standard items: 
1VSD-1MC-20 or VSD-1MC-40 Module 
1 Installation / User’s Guide 

Mounting hardware required 

This is the list of the mounting hardware needed, which is not included with the 
product: 
 

2 conductor wire, non-twisted, AWG #22 
Screws (to mount the module on the wall) 
Screwdriver 
Soldering iron kit or approved sealed connectors 

Summary of Contents for VSD-1MC-20














Reviews: