background image

VSD-1MC-20(40) 

Page 5 

Using the VSD-1MC-20(40) 

With the VSD-1MC-20(40) you can control a variable fan according to a 0-10 Volts or 
4-20 mA input signal. Refer to figure 2 for the location of the different switches, 
jumpers and selectors of the different module. 

Figure 2:  Electronic Boards and Component Location 
 

 

 

1

Minimum Speed Potentiometer 

This potentiometer is used to adjust the minimum speed of the fan. This will be 
the minimum speed when the input signal is at its minimum value.

 

 

2

Dip Switches (Input Range Switch and Shutoff 5% Switch

Dip Switch 1 is used to select the Input Range (ON = 2-10 Volts / 4-20 mA, OFF 
= 0-10 Volts / 0-20 mA). 
Dip Switch 2 is used to adjust the output behavior when the input is below 5% of 
its total range (ON = Shutoff, OFF = Runs continuously at minimum speed). 

 

3

Input Type Jumper 

This jumper is used to select which input type is used. Two types of input can be 
used which are: 0-20 mA (jumper on the 2 left pins) and 0-10 Volts (jumper on 
the 2 right pins). 

 

4

Voltage Selection Switch 

This switch is used to select the input voltage value (115V or 230V).

 

[

2

[

1

[

3

[

2

[

1

[

3

[

4

[

4

Summary of Contents for VSD-1MC-20














Reviews: