background image

 

 

Limitation of Liability/Non-warranty 

For direct or indirect damage to this device or other devices of Vantron caused 

by failure of conforming to this manual or the safety instructions on device label, 

Vantron assumes neither warranty nor legal liability even if the device is still 

under warranty. 

The 

FPC-N64

 should be installed, debugged and maintained by professionals.   

The outside antennas are not permitted to be installed or to be changed by 

non-professionals. To run the device normally, only specified antennas are 

approved to be assembled together by professionals. 

Unit shall be used with indoor-use antenna only. No antenna for this unit can 

be installed outdoor. 

 

Safety Instructions 

  Keep and comply with all operation instructions, warnings, and 

information.   

  Pay attention to warnings on this device. 

  Read the following precautions so as to decrease the danger of injury, 

electric shock, fire, or any damage to the device.     

  Operations and service instructions are provided with the equipment. 

  Unit shall be used with indoor-use antenna only. No antenna for this unit 

can be installed outdoor. 

  The maximum operation temperature is 61°C.   

 

Precautions 

  Pay attention to the product labels/safety instructions printed on silk 

screens. 

  Do not try repairing this product unless declared in this manual. 

  Keep away from heat source, such as heater, heat dissipater, or engine 

casing.   

  Do not insert other items into the slot (if any) of this device.   

  Ensure ventilation of the ventilation slot. 

  System fault may arise if other items are inserted into this device. 

Summary of Contents for FPC-N64






















Reviews: