background image

iii

 

 
 

 

 

Consumer information

 

 
 

Proprietary 
rights

 

The contents of this manual are the property of Vante.  Vante

®

, SEBRA

®

, and 

MINI

™ 

are trademarks or registered trademarks  of Vante in the United States 

and/or other countries. Any  other trademarks noted herein are registered 
trademarks of their respective  owners. Any information and descriptions 
contained in this manual may not be  reproduced, released to the general 
public, or used in conjunction with any  professional instruction without written 
consent of Vante,  USA. Please direct any written inquiries to the appropriate 
address. 

USA  Location 

Representative in Europe:

 

Vante Inc 

Mr. Dmitrij Velikan 

3480 E. Britannia Dr. Suite 120 

Marquip WardUnited GmbH 

Tucson, AZ 85706 

Otto-Hahn StraBe 54 

U.S.A. 

63303 Dreieich-Sprendlingen, Germany 

Tel.  [+1] 520-881-6555 

+49 (0) 6103-3809-66 

Fax [+1] 520-323-9055 

 

 Toll Free: [+1] 877-565-5557                       

 

 

Disclaimer 

This manual is intended as a guide to provide the operator with necessary 

instructions on the proper use and maintenance of certain Vante 
Corporation products. This manual should be used in conjunction with 
instruction and training supplied by qualified Vante personnel. 

Any failure to follow the instructions as described could result in impaired 
product function, injury to the operator or others, or void applicable product 
warranties. Vante accepts no responsibility for liability resulting from  improper 
use or maintenance of its products. 

Utilization  of  Vante  products  may  require  the  operator  to  handle  and 
dispose of blood-contaminated material.  An operator must fully understand 
and implement all regulations governing the safe handling of blood products 
and waste, including the policies and procedures of their facility. 

Handling and use of any blood products collected using Vante  equipment are 
subject to the decisions of the attending physician or other  qualified medical 
personnel. Vante makes no warranty with respect to  such blood products. 

 

 

Summary of Contents for SEBRA MINI 2380


































Reviews: