background image

26

106918

DIRECT-VENT GAS FIREPLACE

VDDVF36PN/PP and VDDVF36STN/STP Series

®

OBSERVED PROBLEM

Burner does not light after pilot is lit

Delayed ignition burner

Burner backfiring during combustion

Slight smoke or odor during initial operation

Fireplace produces a whistling noise when
burner is lit

Glass soots

Fireplace produces a clicking/ticking noise
just after burners are lit or shut off

REMEDY

1. Clean burner or replace burner orifice
2. Contact local propane/LP or natural gas

company

3. Reconnect leads

4. Replace thermopile

1. Contact local propane/LP or natural gas

company

2. Clean burner or replace burner orifice

1. Clean burner or replace burner orifice
2. Replace damaged burner
3. Replace gas control

1. Problem will stop after a few hours of

operation

1. Turn control knob to LO position and

let warm up for a minute

2. Operate burner until air is removed from

line. Have gas line checked by local pro-
pane/LP gas company

3. Clean burner or replace burner orifice

1. Adjust the log set so that the flame does

not excessively impinge on it

2. Inspect the opening at the base of the

burner to see that it is NOT packed with
any type of material

1. This is common. If noise is excessive,

contact qualified service person

POSSIBLE CAUSE

1. Burner orifice clogged
2. Inlet gas pressure is too low

3. Thermopile leads disconnected or im-

properly connected

4. Thermopile is defective

1. Manifold pressure is too low

2. Burner porting or orifice clogged

1. Burner orifice is clogged or damaged
2. Damaged burner
3. Gas regulator defective

1. Residues from manufacturing processes

and logs curing

1. Turning control knob to HI position

when burner is cold

2. Air in gas line

3. Dirty or partially clogged burner orifice

1. Flame impingement on logs

2. Debris around burner air mixer

1. Metal expanding while heating or con-

tracting while cooling

TROUBLESHOOTING

Continued

www.desatech.com

Summary of Contents for VDDVF36STN/STP

































Reviews: