manualshive.com logo in svg

Vanguard 7300 Series, Installation Manual

Share
Download
Vanguard 7300 Series Installation Manual Download Page 18

1-6 

About Vanguard 7300

Vanguard 7300 Functions and Features

Advanced Encryption Card (AEC)

Data Encryption

Data encryption is a very CPU intensive process and is best implemented in 
hardware. Vanguard Managed Solution’s provides a secure hardware-based 
encryption and compression. Release 6.4 and greater supports the Advanced 
Encryption Card (AEC). 

Note

Data compression is not supported on the Vanguard 7300 
Advanced Encryption Card.

The Advanced Encryption Card information is located in Chapter Two of this 
manual. Installation instructions are available in Chapter Five.

For additional information on Encryption configuration refer to the 

Vanguard Data 

Encryption Manual

 (Part Number T0103-09) and the 

Vanguard Virtual Private 

Network (VPN) Manual

 (Part Number T0103-10).

Summary of Contents for 7300 Series




































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands