Vanguard 7300 Series Installation Manual Download Page 176

Page: 176 / 227

6-2

Replacing Power Supplies and Cooling Fans

Replacing Power Supplies and Cooling Fans, 7310 Version 1

Introduction

Power to the Vanguard 7310 Version 1 is provided by two separate power system
components:

• The Power Input Module, which connects with the midplane and brings

power to all of the components in the chassis. The Power Input Module is
accessible from the rear of the enclosure

• The Power Supply/Inlet Fan Module, which also connects to the midplane and

is accessible from the front of the enclosure

Procedures

This section provides procedures that explain:

• Removing and Installing the Power Supply/Inlet Fan Module

• Removing and Installing the Power Input Module

• Removing and Installing the Exhaust Fan Module

• Replacing Power Supplies and Cooling Fans, 7330 Version 1

Figure 6-1 is a diagram that shows the two components and their relationship to the
Vanguard 7310 midplane.

Figure 6-1. Vanguard 7310 Version 1 Power System Components

Power Supply/

Inlet Fan Module

Power Input

Module

Rear of Chassis

Midplane

Summary of Contents for 7300 Series




































































































































































































































Search results

Summary of Contents for 7300 Series

Reviews:

Brands by name

Popular brands

Vanguard 7300 Series, Installation Manual

Search results

Summary of Contents for 7300 Series

Reviews:

Brands by name

Popular brands