Vanguard 7300 Series Installation Manual Download Page 15

Page: 15 / 227

About Vanguard 7300

1-3

Vanguard 7300 Functions and Features

Scalable Hardware
Platforms
Version 2

The Vanguard 7300 Series Version 2 has a new redesigned chassis available in the
following models:

• The 5-slot Vanguard 7310 with built-in dual redundant power supplies

• The 8-slot Vanguard 7330 with built-in dual redundant power supplies

With the Version 2 redesign the Vanguard 7310 5-slot and the Vanguard 7330 8-slot
use the same enclosure, power supplies and fan unit.

Figure 1-2 shows available Vanguard 7300 Version 2 Series routers.

Figure 1-2. Vanguard 7300 Series Routers - Version 2

Vanguard Version 2

7310 and 7330

Summary of Contents for 7300 Series




































































































































































































































Search results

Summary of Contents for 7300 Series

Reviews:

Brands by name

Popular brands

Vanguard 7300 Series, Installation Manual

Search results

Summary of Contents for 7300 Series

Reviews:

Brands by name

Popular brands