background image

13

IOM-3200

Gasket seating surfaces for tank nozzle flange must be clean, free of scratches, 
corrosion, tool marks and flat. Use either a full faced or ring gasket for steel and 
stainless steel raised face flanges
FRP and Aluminum vents are furnished with flat faced flanges. It is recommended 
that they be installed on mating flat face flanges with a full faced gasket.  If the flat 
face of the vent is sealing against a raised face steel flange, a spacer or filler ring 
must be used to fill the annular space of the raised face steel flange.
Refer to Gasket Dimension Table.
Ensure that the gasket material is suitable for the service. 

 

Make sure that the 

gasket is compressed evenly and the flanges are not distorted. Utilizing proper 
torquing techniques will ensure a tight seal and prevent leakage around the 
gasket. See preceding page.

NOTE: 

 Incorrect positioning and/or selection of gasket(s) between the flanges 

will cause bending stresses at the flange that may damage the flange joint 
as bolting is tightened. This is more likely to occur with aluminum or cast iron 
materials.

RECOMMENDATIONS FOR PROPER GASKET INSTALLATION

Correct Installation

Correct Installation

Incorrect Installation

Full Faced Gasket

Spacer and
Full Faced Gasket

Summary of Contents for 3200
















Reviews: