background image

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be 

construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability.  We reserve the right 

to modify or improve the designs or specifications of such product at any time without notice.

Cashco, Inc. does not assume responsibility for the selection, use or maintenance of any product.  Responsibility for proper selection, use and maintenance of any 

Cashco, Inc. product remains solely with the purchaser.

Figure 11 - FRP Vent

TFE ROPE LENGTH

Size

Item 34 *

2”

21”

3”

24”

4”

31”

6”

37”

8”

44”

10”

50”

12”

54”

*  Quantity 2 per unit.

ITEM NO.

DESCRIPTION

1

Body

8

Cover

9

Name Plate  (Not shown)

10

Fibrenut

14

Fibrenut

17

Diaphragm Retainer - Vac

18

Pallet Diaphragm - Vac    ‡

21

Pallet Weights - Vac

ITEM NO.

DESCRIPTION

23

Stem Assy - Vac

24

Diaphragm Retainer - Press

25

Pallet Diaphragm - Press      ‡

28

Pallet Weights - Press

30

Stem Assy - Press

33

Washer (Flat)

34

TFE Rope         ‡

‡   Recommended Spare Part

Summary of Contents for 3200
















Reviews: