background image

Valtir.com

 

Revision D November 2022

 

Safety Symbols 

This section describes the safety symbols that appear in this QuadGuard

®

 manual. Read the 

manual for complete safety and assembly information. 

 Symbol 

Meaning

 

Safety Alert Symbol:

 Indicates Important, Caution, Warning, or Danger. Failure 

to read and follow the Important, Caution, Warning, or Danger indicators could 

result in serious injury or death to the workers and/or bystanders.  

Warning:  

Read safety instructions thoroughly and follow the assembly directions 

and suggested safe practices before assembling, maintaining, or repairing the 

QuadGuard

®

.  It is the responsibility of the installer to follow the instruction 

contained in this manual. Failure to comply with these warnings could result in 

increased risk of serious injury or death in the event of a vehicle impact with a 

system. 

Important:  

Please keep up-to-date instructions for later use and reference by 

anyone involved in the assembly of the product. 

Safety Rules for Assembly 

* Important Safety Instructions * 

This manual must be kept in a location where it is readily available to persons who are skilled and 

experienced in the assembly, maintenance, or repair of the QuadGuard

®

. Additional copies of this 

manual are available from Valtir  by calling (888) 323-6374,  or  by  visiting 

Valtir.com/Contact

Please contact Valtir if you have any questions concerning the information in this manual or the 

QuadGuard

®

It is the responsibility of the installer to use appropriate safety precautions when operating power 

equipment, mixing chemicals, and when moving heavy equipment or QuadGuard

®

 components.  

Safety articles including but not necessarily limited to work gloves,  eye protection,  safety-toe 

shoes, and back protection should be used. 

Warning:  

It is the responsibility of the installer to use all safety measures 

incorporating appropriate traffic control devices specified by the highway authority. 

These measures  must be used to protect all personnel while at the assembly, 

maintenance, or repair site. 

Warning:

  

Failure to comply with these warnings could result in increased risk of 

serious injury or death in the event of a vehicle impact with a system that has not 

been accepted by the FHWA. 

Warning:

  Use only Valtir parts on the QuadGuard

®

 for assembly, maintenance, 

or repair. The use of component parts not specified herein is 

strictly prohibited

The  QuadGuard

®

  assembled with Valtir  Parts has been tested, approved, and 

accepted for state use by the FHWA. A QuadGuard

®

 using parts other than those 

specified herein has not been tested, approved, or accepted for state use by the 

FHWA. Failure to follow this warning could result in increased risk of serious injury 

or death in the event of a vehicle impact. 

Summary of Contents for QuadGuard





































































Reviews: