background image

     

Service and Installation Manual

 

15                                   

For warranty service, call 1-888-VALPRO8 / 1-813-502-030                 

                       

 

 

Operation 

Final Check List before Operation 

1.

 

Have all packing materials and tape been removed from the interior and 
exterior of the ice maker? 

2.

 

Did you clean the ice storage bin?    (See pages 19 - 23) 

3.

 

Have the installation instructions been followed, including connecting the 
machine to water and electricity? 

4.

 

Has the machine been leveled? 

5.

 

Is the ice cube machine in a site where the ambient temperature is between 
50º F (10º C) and 100º F (38º C) and the water temperature between 41º F 
(5º C) and 90º F (32º C) all year round? 

6.

 

Has the water supply pressure been checked to ensure a minimum of 20 
psig with a static pressure not to exceed 80 psig? 

7.

 

Is there a clearance of at least 5

(127 mm) at the rear, top and sides for 

proper air circulation? 

8.

 

Has the power supply voltage been checked or tested against the nameplate 
rating? And has proper grounding been installed for the ice cube machine? 

9.

 

Is the ice cube machine plugged in? 

10.

 

Have you turned on the main water supply and the tap? 

11.

 

Have you checked for leaks at all water supply connections? 

 

Setting Initial Data of Water Filter 

If you use a water filter, before usage the unit should equipped with water filter 
as follow: 

1.

 

Plug in the unit, press the CLEAN button, the ice machine will run 
automatically in Clean mode. The green Clean Cycle LED will be on. Then 
press the CLEAN button more than 6 seconds, it begins to clean, and the 
Cleaning Recommended Indicator Light will be on. And under any 
working status after equipped with water filter, the Cleaning 
Recommended Indicator Light will be on. 

2.

 

Then press the STANDBY button to drain out the water, leave the ice 
machine in the Stand-by mode. If it proceeds to the ice-making stage, 
please press the ICE button to make ice. 

 
 
 
 

   

Service and Installation Manual   

 

 

 

             

For warranty service, call 1-888-VALPRO8 / 1-813-502-030                         

         

12

 
 
 
 
 
 
 
 
 
 
 

                                                      VPIM-55/85 

 

 

 

 

 

VPIM-280 

For VPIM-55/85 ice maker, you will find that the casters make it easy for one 
person  to  move  the  machine.  This  is  useful  for  cleaning  and  sanitizing  the 
surface on which the ice maker is installed because it allows you to move the 
unit and have easy access to the surface to be cleaned. 

IMPORTANT:  When  the  ice  maker  is  ready  to  be  installed  in  a  cabinet  or 
directly  on  the  floor,  you  must  adjust  the  casters  or  the  feet  to  level  the  ice 
maker. For HTIM-55/85 ice maker, if the floor is level, just revolve the plastic 
sheaths of two front casters to touch the floor.

 

Turing the plastic sheath of 
the caster clockwise reduces 
the machine’s height. 
 

Turing the plastic sheath of the 
caster counter-clockwise increases 
the machine’s height. 
 

Turning the under block 
counter-clockwise reduces 
the machine’s height 

up 

Turning the under block 
clockwise increases the 
machine’s height 

Under block 

Summary of Contents for VPIM55

















Reviews: