Valor Madrona Installation Manual Download Page 3

3

x

x

x

B

A

2” 

(52 mm)

minimum

Suggested gas line 
access point through wall. 
Route to avoid optional fan.

Pipe supplied
with engine
(see engine
manual p. 18)

Gas line access
point 10”  (254 mm)

Gas line connection point 
3/8” NPT FEMALE at valve

Gas line 
connection
point 

Sidewall

Mantel

31-7/8”

 (809 mm)

26-1/4”

 (667  mm)

26-11/16” (678 mm)

14-3/4” 

(374 mm)

16-1/4” 

(413 mm)

16-15/16”

 (430 mm)

4-5/8” 
(118 mm)

1”  (26 mm)

minimum

10” (254 mm)

Ø 6-5/8” 
venting

Ø 6-5/8” 
venting

Centre of vent

Hinged 
control
access 
door

27-1/4” (691 mm)

Minimum 61-1/8” (1553 mm)

Front surface 
of stove

M

inimum

18-1/4”

(464 mm)

M

inimum 43-1/4”

 (1091 mm)

M

inimum

12-7/8”

(327 mm)

90°

Zero clearance

Front View

Top View

Right Side View

Corner Dimensions

Alcove Clearances

31-1/4” (794 mm) minimum

26” (660 mm) 

maximum

42” (1067 mm)

minimum

Dimensions & Clearances to Combustibles

Mantel 
Depth ‘A’

0–1”

(0–26 mm)

2–5”

(51–127 mm)

6–18”

(152–457 mm)

19–24”

(483–610 mm)

Mantel 
Height ‘B’

34”

(864 mm)

36”

(914 mm)

38”

(965 mm)

42”

(1067 mm)

Casting Tolerances

Due to the nature of cast iron and concrete, dimen-
sional consistency may vary from one unit to the 
next and some variation in surface fi nish and fl at-
ness is to be expected. We have done our best to 
control and make allowance for this; however some 
variation is inevitable.

Floor Requirements

When the appliance is installed directly on carpeting, 
tile or other combustible material other than wood 
fl ooring, the appliance shall be installed on a metal 
or wood panel extending the full width and depth of 
the appliance.

Mobile Home Floor Fixing

The Madrona stove must be fi xed to the fl oor 
through the fl oor when used in a mobile home.

Mantel Requirements

The Madrona stove may be installed with a 
combustible mantel provided clearances are 
maintained as indicated above. Be aware that 
although safe, some combustible materials and 
fi nishes at the listed clearances may, over time, 
discolor, warp, or show cracks. Care should be 
taken when choosing materials—consult your 
fi replace dealer.

Combustible Mantel Clearances

Summary of Contents for Madrona

















Reviews: