background image

3

Safety Precautions

!

Children and adults should be 

ALERTED

 to the hazards 

of high surface temperature and should 

STAY AWAY

 to 

avoid burns or clothing ignition.

YOUNG CHILDREN

 should be 

CAREFULLY

 

SUPERVISED

 when they are in the same room as the 

appliance. Toddlers, young children and others may 
be susceptible to 

ACCIDENTAL CONTACT BURNS

A physical barrier is recommended if there are at-risk 
individuals in the house. To restrict access to a 

fi

 replace 

or stove, 

INSTALL AN ADJUSTABLE SAFETY GATE

 

to keep toddlers, young children and other at-risk 
individuals out of the room and away from hot surfaces.

DO NOT 

place furniture or any other combustible 

household objects within 36” of the 

fi

 replace front.

READ

 and 

UNDERSTAND

 all instructions carefully 

before starting the installation. 

FAILURE TO FOLLOW

 

these installation instructions may result in possible 

fi

 re 

hazard and will void the warranty.
Prior to the 

fi

 rst 

fi

 ring of the 

fi

 replace, 

READ

 the 

Owner’s Information section of this manual.

DO NOT USE 

this appliance if any part has been under 

water. Immediately, 

CALL

 a quali

fi

 ed service technician 

to inspect the unit and to replace any part of the control 
system and any gas control that has been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be 

PERFORMED

 by a 

quali

fi

 ed service person. The appliance and venting 

system should be 

INSPECTED

 before initial use and at 

least annually by a professional service person. More 
frequent cleaning may be required due to excessive 
lint from carpeting, bedding, etc. It is 

IMPERATIVE

 that 

the unit’s control compartment, burner, and circulating 
air passageways 

BE KEPT CLEAN 

to provide for 

adequate combustion and ventilation air.
Always 

KEEP

 the appliance clear and free from 

combustible materials, gasoline, and other 

fl

 ammable 

vapors and liquids.

NEVER OBSTRUCT 

the 

fl

 ow of combustion and 

ventilation air. Keep the front of the appliance 

CLEAR

 

of all obstacles and materials for servicing and proper 
operation.

Due to the high temperature, the appliance should be 

LOCATED

 out of traf

fi

 c areas and away from furniture 

and draperies.
Clothing or 

fl

 ammable material 

SHOULD NOT BE 

PLACED 

on or near the appliance.

This unit 

MUST

 be used with a vent system as 

described in this installation manual. 

NO

 

OTHER

 vent 

system or components 

MAY BE USED

.

This gas 

fi

 replace and vent assembly 

MUST

 be vented 

directly to the outside and 

MUST

 

NEVER

 be attached 

to a chimney serving a separate solid fuel burning 
appliance. Each gas appliance 

MUST USE 

a separate 

vent system. Common vent systems are 

PROHIBITED

.

INSPECT

 the external vent cap on a regular basis to 

make sure that no debris, plants, trees, shrubs are 
interfering with the air 

fl

 ow.

DO NOT OPERATE

 this appliance with the glass door 

removed, cracked, or broken. Replacement of the glass 
door should be performed by a licensed or quali

fi

 ed 

service person. 

DO NOT

 strike or slam the glass door.

The glass door assembly 

SHALL ONLY 

be replaced 

as a complete unit, as supplied by the 

fi

 replace 

manufacturer. 

NO SUBSTITUTE

 material may be used.

BARRIER DESIGNED TO REDUCE THE RISK OF 

BURNS

 from the hot viewing glass is provided with 

this appliance and 

SHALL BE INSTALLED

 for the 

PROTECTION OF CHILDREN

 and other 

AT-RISK 

INDIVIDUALS

.

DO NOT USE 

abrasive cleaners on the glass door 

assembly. 

DO NOT ATTEMPT

 to clean the glass door 

when it is hot.

If the barrier becomes damaged, the barrier 

SHALL BE 

REPLACED

 with the 

MANUFACTURER’S BARRIER

 

for this appliance.

TURN OFF

 the gas before servicing this appliance. 

It is recommended that a quali

fi

 ed service technician 

perform an appliance check-up at the beginning of each 
heating season.

Any safety screen, guard or barrier removed for ser-
vicing the appliance, 

MUST BE REPLACED 

prior to 

operating the appliance.

BE CAREFUL

 not to put any decorating objects 

sensitive to heat to close above or around the 

fi

 replace 

as it gets very hot when operating.

DO NOT 

use this heater as a temporary source of heat 

during construction.

This appliance is a 

DOMESTIC ROOM-HEATING AP-

PLIANCE

. It must not be used for any other purposes 

such as drying clothes, etc.

State of California. Proposition 65 Warning. 

Fuels 

used in gas, wood-burning or oil 

fi

 red appliances, 

and the products of combustion of such fuels, contain 
chemicals known to the State of California to cause 
cancer, birth defects and other reproductive harm. 
California Health & Safety Code Sec. 25249.6.

The glass door assembly 

MUST

 be in place and sealed 

before the unit can be placed into safe operation.

Summary of Contents for 780JP (LPG)















































Reviews: