background image

When the pilot is off, it will take 2 
minutes before it can be lit again.

TO TURN ON APPLIANCE

TO TURN OFF APPLIANCE

FLAME HEIGHT ADJUSTMENT

•  On the valve, turn MAN knob on the ON, full 

counterclockwise             position.

•  Place ON/OFF switch (if equipped) in I (ON 

position).

STANDBY MODE (Pilot Flame)

•  Press and hold       (small 

fl

 ame) to set appliance at 

pilot 

fl

 ame.

•  Simultaneously press the OFF and

     (large 

fl

 ame) buttons until a short 

beep con

fi

 rms the start sequence 

has begun; release buttons.

•  Continuing beeps con

fi

 rm the 

ignition is in process.

•  Once pilot ignition is con

fi

 rmed, 

there is main gas 

fl

 ow.

•  After main burner ignition the 

handset will automatically go into 
manual (MAN) control mode.

•  Press OFF button.

When the pilot is off, it will take 2 
minutes before it can be lit again.

•  In standby mode: Press and hold

     (large 

fl

 ame) button to increase 

fl

 ame height.

CAUTION

When pilot ignition is con

fi

 rmed, motor turns 

automatically to maximum 

fl

 ame height.

NOTE: Before using the remote control system for 
the 

fi

 rst time, 

the receiver and the handset must be 

synchronized. See the section

 Remote Control Initial 

Set-up

 on page 35 of this manual. 

Set

 (scrolls

through

modes and

settings)

OFF

 (returns

 to set mode,

turns the burner

 and the pilot off )

Large flame 
button (flames
up, sets hours,
temperature)

Small flame 
button (flames
down and off, 
sets minutes, 
temperature)

Current 

temperature

(F or C)

Current time 
(12 or 24 hour clock)

Modes (Manual, 
Temperature, Timer)

Handset 
sensor

Battery status

Current

 programmed

 period (Timer)

Period 

start or end 

(Temp, Timer)

Fan setting (if used)
Burner setting

Display Overview

Handset Overview

Note: In the TEMP or TIMER modes, the remote 
handset senses the room temperature and adjusts the 

fl

 ame accordingly. 

To communicate, the handset should be within 15 feet 
(4.5 meters) of the 

fi

 replace. 

Do not leave the handset on the mantel or hearth.

IMPORTANT:

 

BEFORE YOU BEGIN, please note that 

on this system, the settings of time, temperature and 
automatic ON/OFF can only be programmed when 
the function display is fl ashing
. Be patient when 
programming as it can take a few seconds to set.

Remote Control Operation

10

OWNER’S 
INFORMATION

Summary of Contents for 780JP (LPG)















































Reviews: