background image

9

Vallox

096

MC

© VALLOX • We reserve the right to make changes without prior notice.
What the units include can vary depending on the sales area.

MOUNTING

Mounting 

VALLOX 096 MC has to be mounted in a place where temperature 

does not go below +10 °C. Without protective enclosure, the unit 

must be located in a place with no acoustic disturbance: storerooms, 

technical rooms etc.

Wall mounting

VALLOX 096 MC is mounted on a wall with a mounting plate as 

shown in the adjacent fi gure. Make sure that the unit is horizontally 

level after mounting.

Wall construction

Observe the wall construction during mounting. Avoid mounting the 

unit  on  a  hollow,  echoing  dividing  wall  and  on  a  bedroom  wall 

because of sound conduction, or prevent sound conduction.

Condensing water connections

The delivery includes a water seal. By connecting a pipe to the wa-

ter seal the water condensing from extract air can be led to a fl oor 

drain (not directly to the drain). The pipe must not rise after the water 

seal. The unit has to be mounted horizontally level, so that conden-

sing water can get freely out of the unit.

5

380

165

433

The minimum distance between the top of the unit and the 

fi nished ceiling surface is 30 mm.

162

12

21

20 60

20 30 30

20

60

11

20

30

30

11

84

84

35 30

35

ø7 14kpl

550

30

25

25

Wall mounting plate

30

ϒ

Wall mounting plate

Take into account that the unit 

rises during mounting 10 mm 

higher than the fi nal height.

Bottom edge 

of wall bracket

Pipe outer diameter ø 12 mm

Summary of Contents for 096 MC R













Reviews: