background image

11 

 

 
 
 
 
 
 
 
 
 
 
 
Power Requirements for the ICON LINK unit:

  

 
12v DC: 1.0A MAX  
0.05A - 0.25A during normal operation  
 

Warranty Information:

 

All warranty service provided by the AgSense service center, or an authorized technician. 
  

Warranty repairs require a Return Merchandise Authorization Number (RMA);  
Have your dealer contact AgSense to obtain this RMA number. 

  

For the Period of : 

AgSense will: 

60 Days

 

Money back Guarantee if not satisfied with product. 

2 Years

 

Repair on any unit that fails due to defect in 
materials or workmanship.  AgSense labor and parts 
would be provided free of charge during the 
warranty period. (This does not include dealer 
labor.) 

 

What is not covered: 

 

 Service trips to your home to teach you how to use the product. 

 Improper installation, delivery or maintenance. If you have an installation problem contact your 

dealer or installer. 

 Failure of product resulting from modification to product or due to unreasonable failure to provide 

reasonable and necessary maintenance. 

 Labor necessary to move device from one location to another. 

 Improper installation of battery. 

 Failure due to corrosion or water damage. 

o

 

Units installed in direct contact with sprinklers require a tower box or other watertight 
protection. 

 Damage to the product caused by improper power supply voltage, accident, fire, floods or acts of 

God. 

 Damage caused after delivery. 

 

 
 
 
 
 
 
 
 

Summary of Contents for ICON LINK













Reviews: