15
data). Do not rest pieces with excessive dimensions that
could cause the machine to topple over.
25) PROHIBITED MATERIALS
Cutting metal, wood, plastic, flammable and explosive
materials, and materials that generate harmful or toxic
dust and vapours is prohibited.
26) PREVENT POSSIBLE ACCIDENTS
Always test operations without a work piece before
beginning work; during this operation, make sure no one
gets close to the machine and keep safety distances.
Always use protective goggles, gloves, masks and ear
protection. When the machine is running, do not touch the
blade. Serious injury hazard! After replacing components,
always run a general check before starting work.
27) ONLY USE BLADES SUITED FOR THIS MACHINE
This machine has been designed for using specific blades
for cutting tiles; it is prohibited to use blades suitable
for other materials, abrasive discs or segmented crown
blades. The maximum speed stamped on the blade must
always be higher than that indicated on the machine’s
technical specifications. Use blades which conform to
the regulations in force in the country of use.
28) HANDLE THE BLADE WITH CAUTION
The blade has very sharp edges: handle it with caution and
always wear protective gloves. Serious injury hazard!
29) ONLY USE BLADES IN PERFECT WORKING CONDITIONS
For your safety, do not use damaged, deformed or fissured
blades; if the blade is worn, replace it with a new one.
30) DO NOT FORCE THE BLADE
Do not subject the blade to: collision, bending, excessive
pressure, heat, irregular speed changes, vibrations. In the-
se conditions, the tool has a limited working life and may
break without warning with the risk of flying fragments.
31)
DO NOT TOUCH MOVING PARTS WHILE THE MACHINE
IS RUNNING
WARNING! Serious injury hazard! Do not touch the bla-
de or any part in motion while the machine is running.
Pay attention to arm and hand movements.
32) MACHINE MALFUNCTION
Turn the switch to OFF “O” (switched off), disconnect the
power supply to the machine by removing the plug from
the socket when: not in use, left unattended, moved, the
power cable is damaged, when you are filling the water
tank, during adjustments, maintenance and cleaning.
33) WAIT FOR THE MACHINE TO STOP COMPLETELY
The motor, the moving parts and the blade continue to run for a
short while after the machine is switched off. During this time,
these parts must not be touched. Serious injury hazard!
34) DO NOT LEAVE THE MACHINE UNATTENDED WHILE RUNNING
Do not leave the machine unattended while running and
wait until all moving parts fully stop before leaving the
machine after turning it off.
35) KEEP THE WORKPLACE CLEAN AND TIDY
Mess and dirt are sources of danger. Make sure there
are no tools or objects around the machine that could be
damaged. Do not place tools or objects on the machine
that could accidentally fall. Frequently eliminate the
cutting residuals from the machine and the floor and if
necessary dry the machine and the floor; only carry out
these operations when the machine is stopped and the
power supply cable is disconnected.
36)
THE WATER MUST NOT COME INTO CONTACT WITH
THE ELECTRICAL PARTS
WARNING! Water in contact with electrical parts causes
serious accidents that could be fatal. Only the pump
must be immersed in the water.
37) REPAIRS MUST BE CARRIED OUT BY AUTHORISED
PERSONNEL
Do not attempt to repair this machine or to gain access to its
internal parts. Always contact an authorised assistance cen-
tre. Service by unauthorised personnel will cause the warranty
to be annulled and could create a dangerous situation.
38) REQUEST AND HAVE ORIGINAL SPARE PARTS ONLY
INSTALLED
Request and use only original spare parts. Please contact
your dealer. The use of non-original spare parts will cause the
warranty to be annulled and could create serious danger.
39) STORE THE MACHINE IN A SAFE PLACE
When not in use, keep the machine in a dry place out of
reach of children.
40) RESIDUAL RISKS
WARNING! Strict observance of the instructions with the
use of individual means of protection minimalists risks
of accidents but does not completely rule them out.
41) ALWAYS FOLLOW THESE INSTRUCTIONS
Only use this machine as described in these instructions.
Do not use it for purposes for which it was not intended.
ELECTRICAL SAFETY REGULATIONS
1)
DO NOT TOUCH ELECTRICALLY-POWERED PARTS
WARNING! Risk of electric shocks. Some parts of the
machine are electrically-powered.
2)
OBLIGATION TO USE A CIRCUIT BREAKER
WARNING! Risk of electric shocks. The use of water
with an electrically powered machine increases the
risk of electric shocks which could cause death. For
your safety, it is compulsory to install a circuit breaker
(also called a RCD - residual current device) on the
electric power line for an intervention field according
to the standards in force in the country of use – please
consult your electrician. The RCD provided with the
machine does not provide for exemption from installing
a circuit breaker on the line of the building that supplies
the electrical power in which the machine is used.
3) KEEP CHILDREN AND ANIMALS AWAY FROM ELECTRICAL
DEVICES
Keep children and animals away from the devices con-
nected to the power supply.
4) CHECK THE POWER SUPPLY VOLTAGE
The power supply voltage must correspond to that indi-
cated on the technical data plate. Do not use any other
type of power supply.
5) CONNECTION TO THE POWER SUPPLY
Before connecting or disconnecting the machine to or from
the power supply, make sure that the switch is in the OFF “O”
position. The plug must be positioned vertically sec. fig M.
6) DO NOT TAMPER WITH THE PLUG OR THE POWER
SUPPLY CABLE
It is absolutely forbidden to tamper with the plug and the
power supply cable.
7) CHECK THE POWER SUPPLY CABLE
The power cable and extension cable (where applicable)
must be checked periodically and must be checked for
signs of damage and wear every time they are used. If
they are not found to be in good condition disconnect
them immediately and do not use the machine until an
authorised assistance centre has repaired them.
