background image

Safety 1

0020196671_06 eloSTOR pro Installation and maintenance instructions

3

1

Safety

1.1

Action-related warnings

Classification of action-related warnings

The action-related warnings are classified in
accordance with the severity of the possible
danger using the following warning signs and
signal words:

Warning symbols and signal words

Danger!

Imminent danger to life or risk of
severe personal injury

Danger!

Risk of death from electric shock

Warning.

Risk of minor personal injury

Caution.

Risk of material or environmental
damage

1.2

Intended use

There is a risk of injury or death to the user or
others, or of damage to the product and other
property in the event of improper use or use
for which it is not intended.
The product is designed to generate and
maintain heated drinking water for house-
holds.

Max. hot water temperature: 85

The product is approved exclusively for ver-
tical installation on the wall.
The product must only be operated if a safety
group is installed.
Intended use includes the following:

observance of accompanying operating,
installation and servicing instructions for
the product and any other system compon-
ents

compliance with all inspection and main-
tenance conditions listed in the instruc-
tions.

The use of the product in vehicles, such as
mobile homes and caravans, is not classed
as intended use. Units that are not classed
as vehicles are those that are installed in
a fixed and permanent location (known as
"fixed installation").

Any other use that is not specified in these in-
structions, or use beyond that specified in this
document shall be considered improper use.
Any direct use in industrial or commercial
processes is also deemed to be improper.

Caution.

Improper use of any kind is prohibited.

1.3

General safety information

1.3.1 Risk caused by inadequate

qualifications

The following work must only be carried out
by competent persons who are sufficiently
qualified to do so:

Set-up

Dismantling

Installation

Start-up

Inspection and maintenance

Repair

Decommissioning

Observe all instructions that are included
with the product.

Proceed in accordance with current tech-
nology.

Observe all applicable directives, stand-
ards, laws and other regulations.

1.3.2 Risk of death from electric shock

There is a risk of death from electric shock if
you touch live components.
Before commencing work on the product:

Disconnect the product from the power
supply by switching off all power supplies
at all poles (electrical partition with a con-
tact gap of at least 3 mm, e.g. fuse or cir-
cuit breaker).

Secure against being switched back on
again.

Check that there is no voltage.

1.3.3 Risk of death due to legionella in the

drinking water

Legionellas are pathogens that multiply
quickly at temperatures of up to approx-
imately 50 °C. The legionellas die off at
temperatures of over 60 °C.

Summary of Contents for eloSTOR pro VEH 50/7-3





















Reviews: