6 Operation
16
Installation and maintenance instructions ecoTEC exclusive 0020186710_06
5.10.9 Connecting the circulation pump and
actuating it according to requirements
1.
Carry out the wiring. (
→
Page 14)
2.
Connect the 230 V connection cable to the plug from
slot X13 and plug it into the slot.
3.
Connect the connection cable for the external button
using terminals 1
(0) and 6 (functional drawing) on
the X41 edge connector, which is supplied with the con-
trol.
4.
Plug the edge connector into the PCB slot X41.
6
Operation
6.1
Operating concept
The operating concept and the display and setting facilities
of the operator level are described in the operating instruc-
tions.
An overview of the reading and setting options for the in-
staller level is included in the table in the appendix.
Installer level
–
Overview (
→
Page 32)
6.2
Calling up the installer level
1.
Only call up the installer level if you are a competent
person.
2.
Press
and
at the same time.
3.
Navigate to
Menu
→
Installer level
and confirm by
pressing
.
4.
Set the value
17
(code) and confirm by pressing
.
6.3
Live Monitor (status codes)
Menu
→
Live monitor
Status codes in the display provide information on the pro-
duct's current operating status.
Status codes
–
Overview (
→
Page 40)
7
Start-up
7.1
Switching the product on/off
▶
Press the on/off button on the product.
◁
The basic display appears on the display.
7.2
Running the installation assistants
The installation assistant is displayed whenever the product
is switched on until it has been successfully completed.
It provides direct access to the most important check
programmes and configuration settings for starting up the
product.
To recheck and reset the most important system parameters,
call up the
Appliance config.
.
Menu
→
Installer level
→
Appliance config.
The settings options for more complex systems can be found
in the
Diagnostics menu
.
Menu
→
Installer level
→
Diagnostics menu
▶
Press
to confirm the start of the installation assistant.
◁
All heating and hot water requests are blocked whilst
the installation assistant is active.
Note
If you do not confirm the launch of the install-
ation assistant within 10 seconds of switching
the system on, the basic display reappears.
▶
To access the next point, confirm by pressing
in each
case.
7.2.1
Language
▶
Set the required language.
▶
To confirm the set language and to avoid unintentionally
changing it, press
to confirm this twice.
If you have unintentionally set a language that you do not
understand, proceed as follows to change it:
▶
Press and hold
and
at the same time
.
▶
Also briefly press
.
▶
Press and hold
and
until the display shows the
language setting option.
▶
Select the required language.
▶
Confirm twice by pressing
.
7.2.2
Filling mode
Filling mode (check programme
P.06
) is activated automatic-
ally in the installation assistant for as long as the filling mode
appears on the display.
▶
Fill the heating installation. (
→
Page 19)
7.2.3
Purging
1.
Unlike in the
Check programs
menu, to purge the sys-
tem, start up the check programme
P.00
by pressing
or
.
Hot water circulation
VC 156/5
‑
7
(N-DE)
ecoTEC
exclusive
VC 216/5
‑
7
(N-DE)
ecoTEC
exclusive
VC 246/5
‑
7
(N-DE)
ecoTEC
exclusive
VC 276/5
‑
7
(N-DE)
ecoTEC
exclusive
VC 326/5
‑
7
(N-
DE/DK)
ecoTEC
exclusive
432 l/h
432 l/h
540 l/h
540 l/h
581 l/h
Note
The check programme must run through
completely once, otherwise
S.105
(Product
not purged) is displayed. The product starts
anyway if the specified hot water circulations
(see table) can be achieved. Furthermore,
forced purging takes place. If the check pro-
gramme has run through completely once,
S.105
is cancelled. The product is completely
ready for operation
2.
The purging is time-optimised and adaptive thanks to
the automatic switching between the heating circuit and
the hot water circuit.
