background image

Appendix

12

Operating instructions ecoTEC exclusive 0020193967_01

Appendix
A

Operator level

overview

Setting level

Values

Unit

Increment, select

Default
setting

Min.

Max.

Water pressure

Water pressure

Current value

bar

Live monitor

Status

Current value

Information

Contact details

Phone number

Serial number

Permanent value

Display contrast

Current value

1

25

15

40

comDIALOG

Current value

No function

Basic settings

Language

Current language

Languages available for selection

Country-
specific

Green iQ

Current value

On, Off

On

Display contrast

Current value

1

25

15

40

Resets

Reset anti-cycl. time

Current value

min

B

Troubleshooting

Fault

Cause

Measure

Product does not start
up:

No hot water

Heating remains cold

The gas isolator cock installed on-site and/or the gas
isolator cock on the product is closed.

Open both gas isolator cocks.

The cold water stop valve is closed.

Open the cold water stop valve.

The power supply in the building is disconnected.

Check the fuse in the building. The product
switches on automatically when the power is
restored.

The product is switched off.

Switch on the product (

"Switching on the

product" section).

The heating flow temperature is set too low or to the

Heating off

position, and/or the hot water temperature

is set too low.

Set the heating flow temperature and hot water
temperature (

"Setting the heating flow temper-

ature" section/

"Setting the hot water temperat-

ure" section).

The system pressure is insufficient.
Low water pressure in the heating installation (fault mes-
sage:

F.22

).

Fill the heating installation (

"Filling the heating

installation" section).

There is air in the heating installation.

Have your competent person purge the heating
installation.

After three unsuccessful attempts to ignite the flame, the
product switches to fault mode (fault message: F.

28

).

Press the reset button for one second. The
product makes another attempt to ignite the
flame.
If you have been unable to eliminate the ignition
fault after three reset attempts, consult a com-
petent person.

Summary of Contents for ecoTEC exclusive 627

















Reviews: