Vaillant ecoMAX 824/2 E Instructions For Installation Manual Download Page 36

Page: 36 / 98

Supplied By www.heating spares.co Tel. 0161 620 6677

9 Servicing

• Turn off the boiler CH service valves.
• Turn off the cold water inlet service valve.
• Release the three clamps (1), remove the combustion

chamber cover (2).

9.2.1 For thermoCOMPACT 615, 637 and turboMAX

plus 837

• Remove the flue gas connector (2a) on the fan.
• Remove the retaining spring (3).
• 115

5 k

W:: Pull the three cables (4) and two tubes (5) from

the fan assembly.

• 3

7 k

W:: Remove both plugs (not illustrated) and both

hoses (5) from the fan.

• Remove the fan assembly (6).
• Remove the four screws (7) and detach the front cover

panel from the combustion chamber (8).

• Check the burner (9) and heat exchanger fins (10) and

remove any loose deposits with a soft brush.

9.2.2 For thermoCOMPACT 620, 624, 628,

turboMAX pro 24, 28 and turboMAX plus 824,
828

• Pull the three cables (4) and two tubes (5) from the

fan assembly.

• Remove the fan assembly (6a, 6b, 6c).
• Remove the four screws (7) and detach the front cover

panel from the combustion chamber (8).

• Check the burner (9) and heat exchanger fins (10) and

remove any loose deposits with a soft brush.

• Reassemble in reverse order.
Check central heating expansion vessel.

Note!
It is not necessary to carry out this check every
year – a check every three years should be
sufficient.

• Release the system water pressure from the boiler.
• Remove valve cap from expansion vessel charge point.
• Check that the internal charge pressure of expansion

vessel is between 0.7 - 0.9 bar. If pressure is lower
than this the vessel should be re-pressurised using an
air pump.

• Refit valve cap.
• Open central heating service valves and re-pressurise

the boiler and heating system if necessary.

• Open the gas service valve.
• Turn on the mains power supply.
• Operate the boiler and carry out soundness, safety

and function checks.

• Complete the service interval record section in the log

book and leave with the user.

Instructions for

Fig. 9.1a Cleaning the burner and primary heat exchanger

(thermoCOMPACT 615, 637 and turboMAX plus 837)

Fig. 9.1b Cleaning the burner and primary heat exchanger

thermoCOMPACT 620, 624, 628, turboMAX pro 24,

28 and turboMAX plus 824, 828

Summary of Contents for ecoMAX 824/2 E



































































































Search results

Summary of Contents for ecoMAX 824/2 E

Reviews:

Related manuals for ecoMAX 824/2 E

Brands by name

Popular brands

Vaillant ecoMAX 824/2 E, Instructions For Installation Manual

Search results

Summary of Contents for ecoMAX 824/2 E

Reviews:

Related manuals for ecoMAX 824/2 E

Brands by name

Popular brands