background image

20

Split Type User Manual

7.8 

Emergency Operation and Operation Test

7.8.1  Emergency Operation

Only use this function when the remote controller is 
broken or has been mislaid.
In emergency operation the unit automatically selects 
the operation modes, Cooling or Heating depending on 
the ambient temperature, see Table 7.3.

Temperature Operation Mode

Desired 
Temp.

Timer Mode

Airflow

23ºC

Cooling

26ºC

No

Auto

23ºC

Heating

23ºC

No

Auto

Tab. 7.3 Emergency Operation.

In order to activate:

•  Press the emergency operation/operation test switch.
  A beeping noise is heard which indicates that the 

function has been put into operation.

Fig 7.30 Emergency operation/operation test switch.

Legend

Emergency operation/operation test switch

  Note!

When in emergency operation the dehumidifying 
mode is not available.

7.8.2  Operation Test

Only use this function to carry out operation tests when 
the temperature is less than 16ºC. 
In order to activate:
•  Lift the front lid of the indoor unit.
•  Keep the emergency operation/operation test switch 

pressed for more than five seconds.

  A beep is heard twice which indicates the start of the 

function in cooling mode with the HI (high) airflow 
speed.

•  Release the switch.
  After 30 minutes the function test will end 

automatically.

7.8.3  Cancellation of Emergency Operation/

Emergency Test

•  Press the emergency operation/operation test switch 

once again or use the remote controller.

  The beeping stops.
  The unit returns to normal operating mode.

7 Operating Instructions

Summary of Contents for climaVAIR V 7-025 NW



























Reviews: