Vacon nxsp User Manual Download Page 28

Page: 28 / 31

28 • vacon

fault tracking

Tel: +358-201-2121 • Fax: +358-201-212 205

FAULT TRACKING

The table below presents the faults related to the LonWorks option board. For more information, see
also Vacon NX User's Manual, Chapter 9.
The LonWorks option board status LEDs are described in more detail in Chapter 3.4.

Fault

code

Fault

Possible cause

Correcting measures

Device change

Option board changed.

Reset

Device added

Option board added.

Reset

Device removed Option board removed.

Reset

Device
unknown

Unknown option board.

Fieldbus fault

The received heartbeat time has expired.

Check the installation.
If installation is correct contact the
nearest Vacon distributor.
Please visit:

http://www.vacon.com/wwcontacts.h
tml

Slot fault

Defective option board or slot

Check the board and slot.
Contact the nearest Vacon
distributor.
Please visit:

http://www.vacon.com/wwcontacts.h
tml

Table 7-1. LonWorks option board faults

You can define with parameters how the frequency converter shall react to certain faults:

Code

Parameter

Min

Max

Unit

Step

Default

Note

P2.7.22

Response to fieldbus

fault

0 3

1 0

733

0=No response
1=Warning
2=Fault,stop acc. to 2.4.7
3=Fault,stop by coasting

P2.7.23

Response to slot

fault

0 3

1 0

734

0=No response
1=Warning
2=Fault,stop acc. to 2.4.7
3=Fault,stop by coasting

Table 7-2. Frequency converter responses to faults

Archived Document

Summary of Contents for nxsp
































Search results

Summary of Contents for nxsp

Reviews:

Related manuals for nxsp

Brands by name

Popular brands

Vacon nxsp, User Manual

Search results

Summary of Contents for nxsp

Reviews:

Related manuals for nxsp

Brands by name

Popular brands