V2 AYROS series Installer Manual Download Page 19

ENGLISH

- 42 -

9 - INSTALLATION MENÙ (SEt)

This menu allows you to perform the movements of the gate 
needed during installation.

The automatic learning procedure enables to save run limits based 
on data collected by the encoder.

The manual handling procedure allows to control the gate in hold
to run mode in special cases such as during installation / 
maintenance or a malfunction of the photocells or edges.

m

 

ATTENTION: before proceeding, make sure to position 

the mechanical stops and the limit sensors correctly.

1.

  Press and hold the 

OK

 key until the display shows 

-SEt

2.

  Release the 

OK 

key: the display shows 

ESC 

(only press the 

OK 

key if it is desired to exit this menu)

3.

  Use the keys 

h

 and 

i

 to select the menu 

Mov 

to activate 

manual handling or 

APPr 

to start the automatic learning 

procedure of the run limits

4.

 Press 

OK 

to start the selected procedure

9.1 - AUTOMATIC LEARNING OF THE RUN
LIMITS

m

 

CAUTION: to perform the self-learning procedure it 

is necessary to disable the ADI interface by means of the 
menu 

i.Adi

 . If some safeties are controlled by means of the 

ADI module, they will not be active during the self-learning

NOTE: during the self-learning the slowdown in the limit 
switch area is not active.  
To store the precise position of the range limit it is 
recommended to activate the slow speed near to the limit.
The position at which the slow speed is activated is stored 
as the starting point for slowing down.

5.

  The display shows the control panel and the automatic learning 

procedure of the run limits starts.

 

5.1

  If the gate is not at the closed limit, the motor will  

    activate to close at the slow speed until it reaches the  
  range 

limit.

 

5.2

  Gate opening is activated until the opening limit switch is  

  reached. 
  

NOTE:

 To slow down the motor press the control unit  

  button 

i

 or activate the START P. command (wired or  

    wireless) when the gate comes close to the range limit.

 

5.3

  Gate closing is activated until the closing limit switch is 

  reached. 
  

NOTE:

 To slow down the motor press the control unit  

  button 

i

 or activate the START P. command (wired or  

    wireless) when the gate comes close to the range limit.

6.

  At the end of the automatic learning procedure, the control 

unit automatically exits this menu and returns to normal 
operation.

9.2 - MANUAL HANDLING

m

 

WARNING: when this procedure is activated the

safeties are not active.

5.

  The display shows 

MAn

6.

  Press and hold the 

h

 key to open the gate or the 

i

 button to 

close the gate

7.

  Release the button to stop the gate

8.

  To exit this menu, press 

OK 

NOTE: If the motor is inactive for more than one minute 
the procedure terminates automatically.

APPr

ESC

Mov

MAn

-SEt

Summary of Contents for AYROS series






























Reviews: