V-Trak Backrest User Manual Download

Page: 2 / 32

User manual, installation and adjustment instructions for V-

Trak

Backrest Systems

Contents:

Safety & maintenance

Page

Safety and transportation

Overview

Removal and replacement

Warranty

Maintenance and cleaning

Installation

Installing Mounting Blocks

7-9

Assembling the Central Mount and Arms

Installing the Central Mounting Assembly

Assembling backrest segments

Installing the backrest

Backrest shaping adjustments

Adjusting the backrest shape – Comfort

Adjusting the backrest shape – V-Trak range

15-16

Adjusting the backrest shape – V-Trak segmented backrests

Positional adjustments

V-Trak Lite Hardware

18-20

Height

Backrest angle - Seat depth

22-23

Asymmetrical positioning

Backrest loading

High body mass, high tone, tilt-in-space & recline

24-25

Loading guidelines

26-27

Tissue viability and pressure sores

Security

Safety checklist

28-29

Applications

Selecting a system

30-31

Installation summary

Summary of Contents for Backrest

































Search results

Summary of Contents for Backrest

Reviews:

Related manuals for Backrest

Brands by name

Popular brands

V-Trak Backrest, User Manual

Search results

Summary of Contents for Backrest

Reviews:

Related manuals for Backrest

Brands by name

Popular brands