V-Count 3D Alpha+ User Manual Download Page 45

Page: 45 / 71

3D Alpha+

User’s

Manual

6.1.4

Counting Settings

In this menu, there are quick access to setup wizard menu configuration pages and some
extra configuration pages are present.

6.1.4.1

–

Fi Settings

This page is the same with the Setup Wizard Wi

–

Fi Processing

–

Step 5. Please refer the

previous section.

6.1.4.2

BLE Devices

This page is the same with the Setup Wizard 6.1.2.6. Please refer the previous section.

6.1.5

System Commands

In this menu, system command button present. These are command buttons that does not
link to any web interface page. They directly send commands to device.

Figure 48 System Commands

System commands are:

•

Reset Application: Only resets the application while the device still is powered on.

•

Reboot: Soft power cycle the device

•

Logout: Logouts the current web interface session

“Reset Application” and “Reboot” are required after some system settings.

Summary of Contents for 3D Alpha+








































































Search results

Summary of Contents for 3D Alpha+

Reviews:

Related manuals for 3D Alpha+

Brands by name

Popular brands

V-Count 3D Alpha+, User Manual

Search results

Summary of Contents for 3D Alpha+

Reviews:

Related manuals for 3D Alpha+

Brands by name

Popular brands