background image

IMPORTANT

In accordance with Section 325 (f) (3) of the Energy Policy and 

Conservation Act, this boiler is equipped with a feature that saves energy 

by reducing the boiler water temperature as the heating load decreases.  

This feature is equipped with an override which is provided primarily to 

permit the use of an external energy management system that serves the 

same function.

THIS OVERRIDE MUST NOT BE USED UNLESS AT LEAST ONE OF THE 

FOLLOWING CONDITIONS IS TRUE:

• 

An external energy management system is installed that reduces the boiler water 

temperature as the heating load decreases.

• 

This boiler is not used for any space heating

• 

This boiler is part of a modular or multiple boiler system having a total input of 

300,000 BTU/hr or greater.

• 

This boiler is equipped with a tankless coil.

All specifications subject to change without notice. 

©2020 ECR International, Inc. 

 

2201 Dwyer Avenue, Utica, NY 13501  
Tel. 800 253 7900  

www.ecrinternational.com

BDR THERMEA 

GROUP

Summary of Contents for MACF-150























































































































Reviews: