UTE UH2-44-SET User Manual Download Page 60

Page: 60 / 76

UH2-44: 4x4 HDMI 2.0 HDBaseT Matrix Switcher

U.T.E. electronic GmbH & Co. KG

www.ute.de

Command

Description

Command Example and

Response

STA_HDCP.

Report the HDCP mode of all outputs.

OUT 01 HDCP BYPASS!

OUT 02 HDCP BYPASS!

OUT 03 HDCP BYPASS!

OUT 04 HDCP BYPASS!

OUT 05 HDCP BYPASS!

OUT 06 HDCP BYPASS!

OUT 07 HDCP BYPASS!

OUT 08 HDCP BYPASS!

7.3.5 EDID Management

Command

Description

Command Example and

Response

EDIDMInit.

Reset factory default EDID to all input ports.

All Input EDID Set Default!

EDIDUpgrade[XX].

Upgrade the EDID data of the input port [XX].

[XX]=00~04, U.

[XX]=00, represents all inputs.

[XX]=01~04, represents HDMI input 1~4.

[XX]=U, upload a user-defined EDID. The EDID

can be saved for invoking at any time.

When the command applied, system prompts to

upload the EDID file (.bin). Operation will be

cancelled in 10 seconds. Please disconnect

HDBT connection before sending command to

ensure the data can be received successfully.

EDIDUpgrade01.

EDIDUpgradeU.

256

9600bps

Input XX/User Define EDID

Upgrade OK By RS232 Or

GUI!

EDID/[XX]/[YY].

The input [XX] recall the embedded EDID [YY].

[XX]=00~04.

The “00” represents all inputs.

[YY]=01~07.

[YY]

EDID

1080p 2CH

1080p MultiCH

4K@30Hz HDR 2CH

4K@30Hz HDR MultiCH

4K@60Hz HDR 2CH

4K@60Hz HDR MultiCH

User-defined EDID

EDID/03/01.

Input 03 EDID Upgrade OK

By 01 Internal EDID!

Summary of Contents for UH2-44-SET












































































Search results

Summary of Contents for UH2-44-SET

Reviews:

Related manuals for UH2-44-SET

Brands by name

Popular brands

UTE UH2-44-SET, User Manual

Search results

Summary of Contents for UH2-44-SET

Reviews:

Related manuals for UH2-44-SET

Brands by name

Popular brands