UTE UH2-44-SET User Manual Download Page 47

Page: 47 / 76

UH2-44: 4x4 HDMI 2.0 HDBaseT Matrix Switcher

U.T.E. electronic GmbH & Co. KG

www.ute.de

7.1.2 Control the Matrix Switcher from Remote

To control the matrix switcher from remote location, please connect one or more
PCs to the

RS232

ports of HDBaseT receivers with the

3-pin to DB9 RS232 Cables

The matrix switcher can be controlled by any one of PCs, the connection diagram is
shown as below:



Note:

The command

“

RS232RCM[XX]ON.

” (

[XX]

00~04

) needs to be sent to

enable or disable this control mode. For example, send the command

“

RS232RCM00ON.

”

to enable the remote-control mode for all HDBaseT outputs,

and send the command “

RS232RCM00OFF.

”

to disable the remote-control mode

for all HDBaseT outputs.
Please refer to the 7.3.1 System Control for more details.

AUDIO MATRIX OUT / ARC

IR EYE

LINK

HDCP

Display

Receiver

LINK

HDCP

Display

Receiver

4K Blu-Ray

HDMI:

RS232:

HDBaseT:

Summary of Contents for UH2-44-SET












































































Search results

Summary of Contents for UH2-44-SET

Reviews:

Related manuals for UH2-44-SET

Brands by name

Popular brands

UTE UH2-44-SET, User Manual

Search results

Summary of Contents for UH2-44-SET

Reviews:

Related manuals for UH2-44-SET

Brands by name

Popular brands