UTE UH2-44-SET User Manual Download Page 57

Page: 57 / 76

UH2-44: 4x4 HDMI 2.0 HDBaseT Matrix Switcher

U.T.E. electronic GmbH & Co. KG

www.ute.de

7.3.3 Audio Setting

Command

Description

Command Example and

Response

SPDIF[XX]:[YY].

Select audio source [YY] for SPDIF audio output

[XX]. [XX]

=00~04, The “

[XX]

=00” represents all

SPDIF audio outputs. [YY]=01~12.

[YY]

Audio Source

[YY]

Audio Source

In1 Breakout

Out3 Breakout

In2 Breakout

Out4 Breakout

In3 Breakout

Out1 ARC

In4 Breakout

Out2 ARC

Out1 Breakout

Out3 ARC

Out2 Breakout

Out4 ARC

SPDIF01:04.

SPDIF Out 01 Switch To

Video In 04!

STA_SPDIF.

Report SPDIF audio status.

SPDIF Out 01 Switch To

Video In 01!

SPDIF Out 02 Switch To

Video In 02!

SPDIF Out 03 Switch To

Video In 03!

SPDIF Out 04 Switch To

Video In 04!

AVOLUME[XX]:[YY].

Set the volume of analog L+R audio output [XX]

to [YY]. [XX]=00~04,

The “[XX]=00” represents

all L+R audio outputs.

[YY]

Description

V+

Volume Up

V-

Volume down

Mute

Unmute

00~100

Volume value

AVOLUME00:V+.

AVOLUME00:V-.

AVOLUME01:MU.

AVOLUME01:UM.

AVOLUME01:05.

AVOLUME01:100.

Analog Out 01 Volume 61!

Analog Out 02 Volume 61!

Analog Out 03 Volume 61!

Analog Out 04 Volume 61!

Analog Out 01 Volume

Mute!

Analog Out 02 Volume

Mute!

Analog Out 03 Volume

Mute!

Analog Out 04 Volume

Mute!

Summary of Contents for UH2-44-SET












































































Search results

Summary of Contents for UH2-44-SET

Reviews:

Related manuals for UH2-44-SET

Brands by name

Popular brands

UTE UH2-44-SET, User Manual

Search results

Summary of Contents for UH2-44-SET

Reviews:

Related manuals for UH2-44-SET

Brands by name

Popular brands