background image

11969003 Rev A

 

© 2020 UTC RETAIL 

 

 

All rights reserved. 

Preparing for Installation 

Safety Precautions 

 

DANGER: High Voltage 

 

This unit contains high voltage. There is a risk of electrical shock if the case is opened. If service is required, contact 
an authorized service agent or UTC RETAIL (UTC). 

WARNING: CMOS Battery Damage 

 

Replace your system's battery only with CR-2032 (or equivalent) 3V Lithium-Ion coin cell battery to avoid risk of 
personal injury or physical damage to your equipment. Always dispose of used batteries according to local ordinance, 
where applicable. Any damage due to not following this warning will void your warranty. 

WARNING: Access to Internal Components 

 

All access to internal components of the 2600 POS unit is restricted to Authorized Service Personnel only. Opening the 
case or service by anyone else will automatically void the warranty on this product. 

WARNING: Connect AC Power Cable last 

 

To avoid accidental power-up during installation, connect the AC Power Cable last. 

WARNING: Electrical Shock 

 

Use caution when connecting cables. To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits 
to telephone-network voltage (TNV) circuits. Local Area Network (LAN) ports contain SELV circuits, and telephone 
ports contain TNV circuits.  Some LAN ports and some telephone ports use RJ-45 connectors. 

CAUTION: 

 

Damage to the logic module components may occur if AC power is not removed from the product prior to attaching any 
accessories. 

CAUTION: 

 

Do not 

use the Magnetic Stripe Reader (MSR) unit as a handle when moving or carrying the 2600 POS. 

CAUTION: 

 

Do not 

hot plug to the I/O panel serial ports or the serial port adapter cable. Turn off the 2600 POS Unit before 

connecting serial port cables. 

 

 
 
 
 
 
 
 
 

This document may not be used for any purpose other than its intended use. This document 
must be downloaded in its entirety; it may not be reproduced, stored or transmitted in part 
without the prior written permission of UTC RETAIL. All attempts have been made to ensure 
that the information presented in this document is correct. No liability, expressed or implied, will 
be assumed by UTC RETAIL, its dealers, or affiliates, for damage resulting from the use of this 
information.

 

 

Summary of Contents for 2600 POS








Reviews: