Uson Qualipak-770 Manual Download Page 27 | Manualshive

Page: 27 / 27

background image

25

•

Check calibration of the transducers. This can be carried out by Uson service
engineers. It is advisable to arrange a service contract so that calibration checks
are carried out automatically by an engineer. Contact the service manager at Uson
Ltd. for details.

Cleaning

Clean the inside and outside of the chamber with a light alcohol wipe, avoiding the green
painted area.

User changeable Spare parts

Q171336

Lid Seal

Q7/4634

Gas struts (pair)

Q7/4637

AV Mounts

For other parts contact Uson or local Agent

«
...
25
26
27

Summary of Contents for Qualipak-770




























Reviews:

No comments

Related manuals for Qualipak-770

Brand: KaVo Pages: 16

Brand: Campbell Pages: 18

Brand: Vector Pages: 4

Brand: Salvis Pages: 40

Brand: IDEAL Pages: 2

Brand: GE Pages: 24

Brand: Yamaha Pages: 50

Brand: A&D Pages: 30

Brand: BACtrack Pages: 13

Brand: TA Instruments Pages: 35

Brand: Gearmore Pages: 47

Brand: Xtool Pages: 51

Brand: H-TEC Education Pages: 16

Brand: H-TEC Education Pages: 12

Brand: Panta Safe Light Pages: 2

Brand: Calrec Pages: 70

Brand: Radial Engineering Pages: 16

Brand: R&S Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands