manualshive.com logo in svg

USC LPV Series, Operator'S Manual

Share
Download
USC LPV Series Operator'S Manual Download Page 21

Page 21 

LPV SEED TREATER 

LPV AUTOMATED TREATER SET 

-

 UP (ALL TREATERS)

 

After the actuator is installed it should move freely by hand.

 

If something is binding, damage to the actuator or the mounting 
brackets could occur.

 

 
 

Après l'actionneur est installé, il doit se déplacer librement à la main.

 

Si quelque chose est obligatoire, les dommages à l'actionneur ou les 
supports de montage pourrait se produire.

 

NOTICE

 

 

AVIS

 

 

6.

 

Anchor the seed treater in position to prevent the machine from moving during     
operation.

 

7.

 

Inspect machine thoroughly for screws, bolts, fittings, etc. which may have come 
loose during shipping.

 

8.

 

The pump stand(s) should be placed on level ground close to the seed treater.

 

9.

 

Attach the chemical tubing from the pump stand(s) to the static mixer on the seed 
treater (below).  Additional tubing may be added or removed to accommodate your 
installation.

 

Static Mixer     

Assembly 

Summary of Contents for LPV Series
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands