US Water Systems Ultimate Dual Superfilter FSF-250 Owner'S Manual Download | Manualshive

Page: 18 / 31

background image

18

Visit us online at www.USWaterSystems.com Give us a call at: 1-800-608-8792

Installation Instructions

6. Using the Allen Key (included), place the unit in the bypass position (See below for by-
pass valve handle placement). Slowly turn on the main water supply. At the nearest cold
treated water tap nearby remove the faucet screen, open the faucet and let water run a few
minutes or until the system is free of any air or foreign material resulting from the plumbing
work.
7. Make sure there are no leaks in the plumbing system before proceeding. Close the water
tap when water runs clean.
8. Proceed to start up instructions.

Note: The unit is not ready for service until you complete the start-up instructions.

«
...
16
17
18
19
20
...
»

Summary of Contents for Ultimate Dual Superfilter FSF-250
































Reviews:

No comments

Related manuals for Ultimate Dual Superfilter FSF-250

Brand: lancer Pages: 48

Brand: A.O. Smith Pages: 65

Brand: A.O. Smith Pages: 2

Brand: Zip Pages: 12

Brand: WaterCare Pages: 7

Brand: UFESA Pages: 20

Brand: Tecnosystemi Pages: 12

600 LFCV Series

Brand: lancer Pages: 32

Brand: Frigidaire Pages: 21

Brand: Atlantic Pages: 88

Indispensable KCH-06076

Brand: Honey Can Do Pages: 8

Brand: Kitchen Living Pages: 32

Brand: WaterLogic Pages: 12

Brand: SolarPower Pages: 20

Brand: Modena Pages: 9

Brand: KYOWA Pages: 3

Brand: KYOWA Pages: 3

Brand: TANKLESS Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands