manualshive.com logo in svg

US Robotics USR5462, User Manual

Share
Download
US Robotics USR5462 User Manual Download Page 71

67

REGULATORY AND WARRANTY

802.11g 54Mbps Router User Guide (Windows 95, 98, 2000, NT, Me, XP, and 
Macintosh)

Regulatory Information

 

FCC Declaration of Conformity

This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired opera-
tion.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If 
this equipment is not installed and used in accordance with the manufacturer’s instructions, it may cause 
harmful interference to radio communications. However, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required to assure compli-
ance with FCC regulations. Modifications to this unit not expressly approved by the party responsible for 
compliance could void the user’s authority to operate this equipment.

FCC Channel Restriction

U.S. Robotics declares that USR5462 (FCC ID:RAXWG4005D-U5) is limited in CH1~CH11 by specified firm-
ware controlled in the U.S.A.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This 
equipment should be installed and operated with minimum distance 20 cm between the radiator and your 
body.

UL Listing/CUL Listing

This information technology equipment is UL-Listed and CUL Listed for the uses described in the users 
guide.

Industry Canada Statement

This equipment complies with the Industry Canada Spectrum Management and Telecommunications policy, 
RSS-210, standard Low Power License-Exempt Radio Communication Devices.
Operation is subject to the following two conditions:
1.This device may cause interference.
2.This device must accept any interference, including interference that may cause undesired operation of the 
device.

CE Declaration of Conformity

We, U.S. Robotics Corporation of 935 National Parkway, Schaumburg, Illinois, 

60173-5157,USA, declare under our sole responsibility that the U.S. Robotics Wireless Turbo Access Point & 
Router to which this declaration relates is in conformity with the following standards and/or other normative 

0560

Summary of Contents for USR5462















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands