US Robotics USR5462 User Manual Download Page 52 | Manualshive

Page: 52 / 78

background image

Configuring the 802.11g 54Mbps Router

48

Intrusion Detection

•

SPI and Anti-DoS (Denial-of-Service) firewall protection (Default:
Enable) – The Intrusion Detection Feature limits access for
incoming traffic at the WAN port. When the SPI (Stateful Packet
Inspection) feature is turned on, all incoming packets will be
blocked except for those types marked with a check in the
Stateful Packet Inspection section.

•

Discard Ping from WAN (Default: Enable) – Prevents the router
from responding to any PING request on the WAN port.

•

E-mail Alert Configuration – Enter your email address. Specify
your SMTP and POP3 servers, user name, and password.

«
...
50
51
52
53
54
...
»

Summary of Contents for USR5462















































































Reviews:

No comments

Related manuals for USR5462

Brand: D-Link Pages: 8

Brand: D-Link Pages: 47

Brand: D-Link Pages: 72

Brand: Lancom Pages: 101

DIR-451 - 3G Mobile Router

Brand: D-Link Pages: 83

DWL-2100AP - AirPlus Xtreme G

Brand: D-Link Pages: 2

Brand: D-Link Pages: 8

DI-711 - Gateway

Brand: D-Link Pages: 7

Brand: D-Link Pages: 100

DI-514 - Wireless Router

Brand: D-Link Pages: 62

Brand: D-Link Pages: 20

Brand: D-Link Pages: 47

Brand: Panasonic Pages: 2

Brand: TCL Pages: 22

Brand: ALCON Pages: 46

Brand: Harman Pages: 36

IEEE 802.1n Wireless Series

Brand: Longshine Pages: 33

Brand: Alvarion Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands