manualshive.com logo in svg

US Robotics USR5462, User Manual

Share
Download
US Robotics USR5462 User Manual Download Page 36

Configuring the 802.11g 54Mbps Router

32

summary of wireless security considerations is listed in the following 
table.

Security 
Mechanism

Client 
Support

Implementation Considerations

WEP

Built-in support on all 
802.11b and 802.11g 
devices

• Provides only common security
• Requires manual key management

WPA mode

Requires WPA-enabled 
system and protocol 
driver for network 
adapter 

(native support provided 
in Windows XP)

• Provides good security in small 

networks

• Requires configured RADIUS server, 

or manual management of pre-shared 
key

802.1x mode

Requires WPA-enabled 
system and network 
adapter driver

(native support provided 
in Windows XP)

• Provides robust security in WPA-only 

mode (i.e., WPA clients only)

• Requires configured RADIUS server
• 802.1x Extensible Authentication 

Protocol (EAP) type may require 
management of digital certificates for 
clients and server

Summary of Contents for USR5462















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands