manualshive.com logo in svg

US Robotics USR5462, User Manual

Share
Download
US Robotics USR5462 User Manual Download Page 10

Installing the 802.11g 54Mbps Router

6

Turn on your cable or DSL modem. Connect the included power adapter to 
the power socket on the 802.11g 54Mbps Router. Plug the power adapter 
into a standard power outlet. Turn on your computer.

Step Three: Configure the basic connection settings

Note:

You will also need to verify that the HTTP Proxy feature of 
your web browser is disabled. Refer to “Troubleshooting” 
on page 57.

Perform the steps of the Setup Wizard to configure the basic connection 
settings of the 802.11g 54Mbps Router.

Your Internet connection user name and password will be required for the 
installation of the 802.11g 54Mbps Router. Depending on your ISP, you may 
need to know some of the following information: IP Address, Subnet Mask, 
Gateway/Router, DNS Servers/ Name Servers, and Service Name 
(optional). 

Note: 

To obtain the necessary information, first look within your login appli-

cation. If you cannot find all the necessary information, contact your ISP for 
assistance in obtaining this information.

Summary of Contents for USR5462















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands