3.2 Technical Specifications
3.2.1 Tool Technical Specifications
Item / Model
UBX-AF500Z
UBX-AF600Z
UBX-AF700Z
Bolt Capacity
M6-M8
M8-M10
M8-M12
Torque Range
Nm
5.0
～
20.0
15.0
～
40.0
25.0
～
60.0
Fastening Cycle
Note 1
11 fasteners / min.
10 fasteners / min.
9 fasteners / min.
Free Speed
Note 2
min
-1
1000
– 3600
1000 - 4800
Drive Shank Size
mm
9.5Sq
Overall Length
mm
219
Weight
Note 3
kg
1.83(1.53)
1.88(1.53)
1.93(1.58)
Sound Pressure Level (L
pA
)
dB(A)
<70
73
72
Sound Uncertainty
dB(A)
3
Vibration Total Value (A
hd
)
m/s
2
<2.5
Vibration Uncertainty (
K
)
m/s
2
0.59
0.60
0.61
Reaction Moment
Nm
0.8
1.0
Trigger Force
N
8.0
Battery Voltage (DC)
V
10.8
14.4
Motor Speed
Note 4
min
-1
Initial Speed (up to START torque)
Settable per 100 min
-1
increments
from 1000 min
-1
to 3600 min
-1
Initial Speed (up to START torque)
Settable per 100 min
-1
increments from 1000 min
-1
to 4800 min
-1
Speed (from START to CUT torque)
Settable per 100 min
-1
increments
from 1300 min
-1
to 3600 min
-1
Speed (from START to CUT torque)
Settable per 100 min
-1
increments from 1300 min
-1
to 4800 min
-1
Motor Power
Note 4
(Current Level)
－
Settable in 2 steps (till and after START Torque) from 4 levels
IEC62841-1 and IEC62841-2-2 are applied. Protection against electric shock is Class I.
Note
1
…Fastening Condition : Fastening Time Approx. 0.5 sec/fastener at ambient temperature of 18 °C (64.4°F)
Note
2
…Free speed increases in 3 steps, 500min
-1
→ 1000min
-1
→ Initial Speed Value
Note
3
…Weight f/w 2.0Ah battery pack (see P.8). Value inside ( ) shows weight w/o battery pack.
Note
4
…Settable combination of Motor Power (Current Level) and Motor Speed Range
Current Level 1 : 13 (1300min
-1
) ~ 48 (4800min
-1
), Current Level 2 : 17 (1700min
-1
) ~ 48 (4800min
-1
)
Current Level 3 : 21 (2100min
-1
) ~ 48 (4800min
-1
), Current Level 4 : 25 (2500min
-1
) ~ 48 (4800min
-1
)
3.2.2 ZigBee Specifications
Frequency
2.4GHz (2.405 - 2.48Hz 16ch)
Output
10mW
Modulation and Communication System
Offset phase orthogonal modulation system
Spread System
Direct spread spectrum communication system
Communication Distance
Radius of approx. 20m
*Note
ID Setting
7 Bit Dip Switch (128 ways)
*NOTE: The communication may not be established at the place where radiation noise such as electric welding exists.
If there is a place where the communication is not established even in a short distance between the transmitter
and the receiver, there may be a dead point which is generated by a reflected wave.
13
These declared sound and vibration values given in the above table were obtained by laboratory
type testing in accordance with
EN 62841-1 for sound levels
and
ISO 28927-2
for vibration
values
and are not adequate for use in risk assessments. Values measured in individual work
places may be higher than the declared values. The actual exposure values and risk of harm
experienced by an individual user are unique and depend upon the way the user works, the
workpiece and the workstation design, as well as u ppon the exposure time and the physical
condition of the user.
We, URYU SEISAKU, LTD., cannot be held liable for the consequences of using the declared
values, instead of values reflecting the actual exposure, in an individual risk assessment in a work
place situation over which we have no control.
Summary of Contents for UBX-AF Series
Page 20: ...Exploded View 18...
Page 25: ......
