Ursalink UR75 Edge User Manual Download Page 25

Page: 25 / 169

UR75 User Guide

Figure 4-1-2-1

Modem Information
Item

Description

Status

Show corresponding detection status of module and SIM card.

Model

Show the model name of cellular module.

Current SIM

Show the current SIM card used.

Signal Level

Show the cellular signal level.

Show the registration status of SIM card.

IMSI

Show IMSI of the SIM card.

ICCID

Show ICCID of the SIM card.

ISP

Show the network provider which the SIM card registers on.

Network Type

Show the connected network type, such as LTE, 3G, etc.

PLMN ID

Show the current PLMN ID, including MCC, MNC, LAC and Cell ID.

LAC

Show the location area code of the SIM card.

Cell ID

Show the Cell ID of the SIM card location.

IMEI

Show the IMEI of the module.

Table 4-1-2-1 Modem Information

Summary of Contents for UR75 Edge










































































































































































Search results

Summary of Contents for UR75 Edge

Reviews:

Ursalink UR75 Edge, User Manual, Page: 25 / 169

Search results

Summary of Contents for UR75 Edge

Reviews: