background image

11

E N G L I S H •

User’s manual

• Do not operate this tool while under the in-
fluence of drugs, alcohol, or any medication. 
• Always stay alert. 
Do not allow familiarity, 
gained from frequent use of your grinder, to 
cause a careless mistake. 
• Always remember that a careless fraction of 
a second is sufficient to inflict severe injury.
• Never reach to pick up a workpiece, a piece 
of scrap, or anything else that is in or near the 
grinding path of the wheel. 
• Avoid awkward operations and hand posi-
tions
 where a sudden slip could cause your 
hand to move into the wheel. Always make 
sure you have good balance.
• Do not use tool if switch does not turn it on 
and off.
 Have defective switches replaced by 
an authorized service center.
• Do not turn the motor switch on and off 
quickly.
 This could cause the wheel to loosen 
and could create a hazard. Should this ever oc-
cur, stand clear and allow the wheel to come 
to a complete stop. Disconnect your grinder 
from the power supply and securely retighten 
the wheel nut.
• If any part of this grinder is missing or should 
break, bend, or fail in any way, or should any 
electrical component fail to perform properly, 
shut off the power switch, remove the machine 
plug from the power source and have dam-
aged, missing, or failed parts replaced before 
resuming operation.
• Make sure the grinder is securely mounted as 
described in the operating instructions before 
connecting the tool to a power supply.
• Do not overtighten the wheel nut. Excessive 
tightening can cause the wheel to crack during 
operation.
• Inspect grinding wheel for visible defect. 
Check the wheel for fissures and cracks. Re-
place defective wheels prior to use.
• Adjust distance between wheel and work rest 
to maintain 1/16” (1,6 mm). Or less separation,  
readjustment is necessary as the diameter of 
the wheel decreases with use.
• Always ease the workpiece against the abra-
sive wheel
 when starting to grind. A hard im-
pact can break the wheel. Use light pressure 
when starting to grind; too much pressure on a 
cold wheel can cause the wheel to crack.

FEATURES

KNOW YOUR TOOL
Before attempting to use your new tool, 

 

familiarize yourself with all operating features 
and safety requirements. Carefully read this 
operator’s manual before using your grinder.

ON / OFF SWITCH (1)
Your bench grinder features a front access on / 
off switch for convenience and safety.

GRINDING WHEEL (2)
Equipped with course and fine grinding wheels 
to suit most applications.

SAFETY SHIELD AND SPARK DEFLECTOR (3)
The safety shields and spark deflectors are ad-
justable for operator convenience. 
Operating the grinder without these features 
attached could result in serious injury. Do not 
grind with the safety shield raised; always wear 
safety glasses for personal protection.

WORK REST (4)
The work rests are independently adjustable 
to compensate for wheel wear. Before grind-
ing, make certain the work rests are adjusted  
properly. Generally the object being ground 
is done slightly above center of the grinding 
wheel. Adjust the distance between the wheel 
and the work rest to maintain 1/16” (1,6 mm) 
or less separation as the diameter of the wheel 
decreases with use.

ASSEMBLY INSTRUCTIONS

 WARNING: always disconnect the bench 

grinder from the power source before per-
forming any assembly or adjustment. Failure to 
do so could result in accidental starting result-
ing in possible serious personal injury.
SPARK DEFLECTOR

2

3

4

1

EB205B manual.indd   11

03/09/15   17:12

Summary of Contents for Foy EB205B

















Reviews: