APARTMENT DOOR PHONE STATIONS
sec.5a
−−−−
5
DIGIVOICE - Technical Manual
After 3 seconds or when the call button is pressed, the switchboard
station will be activated in the operating mode it was in the last time it
was turned off.
If the switchboard station is in DAY service, LED
will be on.
If the switchboard station is in NIGHT service, LED
will be off.
In both cases, the display will show the following message when the
switchboard station is not in use:
Where, 000 is the switchboard station code.
The switchboard station display features LED backlighting with a 15”
timeout. Backlighting is activated when the handset is picked up, a key
is pressed, or a call or alarm signal is received.
To turn off the switchboard station, hold down the
SHIFT
key
while pressing the
ON
OFF
button.
Note
:
if the switchboard station has never been configured, the
message “CONFIGURATION REQUIRED” will appear on the
display instead of “SYSTEM OK”.
Case 2: Switchboard station with access password
The switchboard station is activated by pressing the
ON
OFF
button.
The display will show the following message for 3 seconds:
The number of the software release is shown at the top of the display.
Enter the access password programmed by the installer, which will
be shown as a sequence of asterisks on the bottom line of the
display. Then press the call button
. The switchboard station will be
activated in the operating mode it was in the last time it was turned
off.
If the password is incorrect or if 1 minute has passed since the
ON
OFF
button was pressed, the switchboard station will be deactivated.
If the switchboard station is in DAY service, LED
will be on.
If the switchboard station is in NIGHT service, LED
will be off.
In both cases, the display will show the following message when the
switchboard station is not in use:
Where, 000 is the switchboard station code.
The switchboard station display features LED backlighting with a 15”
timeout. Backlighting is activated when the handset is picked up, a key
is pressed, or a call or alarm signal is received.
To turn off the switchboard station, hold down the
SHIFT
key
while pressing the
ON
OFF
button.
Note
:
if the switchboard station has never been configured, the
message “CONFIGURATION REQUIRED” will appear on the
display instead of “SYSTEM OK”.
DAY SERvICE
In this operating condition, the switchboard station can be programmed
for three different modes: MODE A, MODE B, and MODE C. All
switchboard stations in the system must be programmed for the same
mode (A, B or C).
Mode A - Call interception enabled
In this mode, the switchboard station provides concierge service,
intercepting calls from main entrance panels to apartment stations.
Calls belong to the zones for which the switchboard station is
configured will be intercepted, as well as all calls to code 0 (i.e., calls
made simply by pressing the entrance module call button) and calls
directed to the code programmed in the switchboard station. Other
calls are sent directly to the apartment stations; if the latter belong
to the zone assigned to another switchboard station, the calls may
be intercepted by it. The switchboard station can call any apartment
station.
The switchboard station will normally receive calls from the apartment
stations only if they belong to its assigned zone. If desired, the
switchboard attendant can take these calls. If the attendant does not
answer the calls, they will be stored in memory. The switchboard
station can also be configured so that calls originating from apartment
stations are completely ignored. In this case, the switchboard station
will neither ring nor store the calls in memory.
Mode B - Call interception NOT enabled
This operating mode is similar to that described above for NIGHT
service.
The switchboard station does not receive calls from outside the
building, but can call the apartment stations and receive calls from
them.
Mode C - Calls from main entrance panels disabled
In this operating mode, calls cannot be put through from any of the
main entrance modules. The switchboard station intercepts calls from
the main entrance panels in the same way as described for Mode A;
in this case, however, the switchboard station does not ring and puts
the main entrance panel in busy status to indicate that the operation
cannot be carried out. Operation as regards calls to apartment stations
is as described for Mode A.
APARTMENT STATION Option
This option can be selected during configuration in cases where the
switchboard station operates in NIGHT service and in DAY A or DAY
B service.
The switchboard station will operate as if it were an ordinary apartment
station, using the code for which it was configured.
OPERATING INSTRUCTIONS
ACTIvATION AND DEACTIvATION
Case : Switchboard station without access password
The switchboard station is activated by pressing the
ON
OFF
button.
The display will show the following message for 3 seconds:
The number of the software release is shown at the top of the display.
GUARD DOOR SWITCHBOARD STATION Ref. 038/40
OPERATING INSTRUCTIONS
REL1.0
SYSTEM OK
---------
23/05/2000 08:10:54
0001
REL1.0
SYSTEM OK
---------
ENTER PASSWORD
23/05/2000 08:10:54
0001
GUARD DOOR SWITCHBOARD STATION
Ref.
038/40
