RANDOM FUNCTION
TROUBLESHOOTING
PROGRAM
ON/OFF
CD
SET
RANDOM
RESET
3
2
1
short/
random
long
programmable random
PROGRAM
ON/OFF
CD
SET
RANDOM
RESET
2
1
4
3
LCD display seems “frozen”. Buttons
won’t respond.
Timer loses programs when unplugged
Programmed ON/OFF times don’t
execute
Programmed ON/OFF times don’t
execute at specified times.
Transmitter stops turning receiver on
and off.
Press reset button to reset timer.
Replace batteries.
Ensure that the program disable feature is
not enabled.
Ensure that the random function is not
enabled.
Use the LEARN function to reprogram the
receiver or check the batteries.
problem
solution
TECHNICAL SPECIFICATIONS
Programmable Timer RCT100
Ratings: 120V AC, 15A
Max Load: 1800W resistive; 600W tungsten
Photocell Transmitter RT601
Transmission Range: up to 40m in open area
Transmission Frequency: 433.92 M z
H
PHOTOCELL TRANSMITTER
2
Repeat
and
for additional timers (available at your local retailer).
Press and hold ON/OFF and
together on timer while
simultaneously pressing the RF
button on the transmitter. (The
green LED indicator on the
transmitter will flash when RF is
pressed).
1
1
Plug timer into wall socket
2
LEARN
PROGRAM
ON/OFF
CD
SET
RANDOM
RESET
1
*
1
The transmitter uses an intelligent code system to prevent interference
from other sources. But if you do experience such interference, you can
press the NEW CODE button to generate a new random house code.
However, after pressing the NEW CODE button, you will need to redo the
LEARNING procedure as described above.
The photocell transmitter can control multiple remote programmable timers.
2
*
1
learn function
PHOTOCELL TRANSMITTER
Transmits an “ON” command to the timer when photocell
senses a change from dark to bright. Transmits an “OFF”
command after the time delay as set by the Timing
Control Dial or when it turns from bright to dark.
3
Once the learn function has been successfully executed,
the
symbol will flash on the top right corner of the LCD
on the timer, every time the transmitter sends a signal or
when the RF button is pressed.
3
day mode / night mode
The photocell transmitter works by detecting the brightness level of its
surroundings and sends ON or OFF commands to the timer. The transmitter can
be set to trigger the timer to run for 30mins, 1, 2, 4, 6, 8, 10hrs or continuously,
and will automatically turn the timer OFF when the photocell senses a change
from dark to bright (in NIGHT mode) or bright to dark (in DAY mode).
Transmits an “ON” command to the timer when photocell
senses a change from bright to dark. Transmits an “OFF”
command after the time delay as set by the Timing
Control Dial or when it turns from dark to bright.
DAY MODE:
NIGHT MODE:
Turn TIMING CONTROL DIAL to select delay off time.
(30 minutes, 1, 2, 4, 6, 8, 10 hours, or continuous)
Slide MODE SWITCH:
for DAY mode
and
for NIGHT mode
up
down
2
2
INSTRUCTION TO THE USER
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and if not installed and used in accordance with the
instructions , may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
In order to maintain compliance with FCC regulations, shielded cables must
be used with this equipment. Operation with non-approved equipment or
unshielded cables is likely to result in interference to radio and TV reception.
The user is cautioned that changes and modifications made to the
equipment without the approval of manufacturer could void the user’s
authority to operate this equipment.
!!
!
!
This device complies with Part 15 of the FCC Rules and RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
FCC / RSS-210 COMPLIANCE
PHOTOCELL TRANSMITTER
!
!
!
!
!
For safety, set the photocell transmitter to trigger the
lights ON inside your doorway at dusk.
For convenience, set the photocell transmitter to start
your coffee maker at first light.
For security, set the transmitter to activate lights in
your home while you are away (day or night).
For energy savings, set the transmitter to trigger your
timer for controlled periods of time.
To maximize functionality, combine the time settings of
the photocell transmitter with those of the
programmable timer to achieve your desired ON/OFF
applications.
applications
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including
interference that may cause undesired operation.
Flashing
for short random
Flashing
for long random
1
2
Press RANDOM
3
Short random from
OR Long random from
CD
RND
L RND
-
* Short random 1-2 hours, long random 2-3 hours
1
2
Press RANDOM
Set program 20 to desired random time
3
3
Select program 20 with
Solid
for programmable
RND
* Programmable random only works with program 20; 1-2 hours
4
Deactivate random function with RANDOM or ON/OFF
PAGE 4
PAGE 5
PAGE 6
PAGE 12
PAGE 11
PAGE 10